Dueemme Sidol · Pipe supports

Downpipe clamps

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Downpipe clamps · AI01
Representative type image

Characteristics and selection criteria

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Selection information

Installation and connection checks

Identify the configuration, check the complete load path to the substrate and apply the design-specific installation sequence. Avoid excessive liner compression and separately verify sliding-support or fixed-point operation.

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Series and technical tables

Pre-painted downpipe clampPre-painted downpipe clampDM-CD01 · 3 configurationsDescription and technical table ↓
Pre-painted downpipe clamp
Representative type image; use the table for the specific design and dimensions.

Characteristics

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Body material: Steel. Liner: Unlined.

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Use the configuration reference and size in your technical enquiry.

Configuration technical table

Dimensions are in mm where stated; G identifies the listed connection. B, H and other letters retain their configuration-specific definitions: request technical review for the dimensioned drawing. Plug dimensions are not pipe diameter.

Pre-painted downpipe clamp · DM-CD01
ReferenceSizeØ [mm]GB [mm]H [mm]b x s [mm]
DM-CD01-0180M81268625×0,6
DM-CD01-02100M814410625×0,6
DM-CD01-03120M817312225×0,6

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Zinc-plated downpipe clampZinc-plated downpipe clampDM-CD02 · 3 configurationsDescription and technical table ↓
Zinc-plated downpipe clamp
Representative type image; use the table for the specific design and dimensions.

Characteristics

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Body material: Steel. Liner: Unlined.

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Use the configuration reference and size in your technical enquiry.

Configuration technical table

Dimensions are in mm where stated; G identifies the listed connection. B, H and other letters retain their configuration-specific definitions: request technical review for the dimensioned drawing. Plug dimensions are not pipe diameter.

Zinc-plated downpipe clamp · DM-CD02
ReferenceSize Ø [mm]GB [mm]H [mm]b x s [mm]
DM-CD02-0180M81268625×0,6
DM-CD02-02100M814410625×0,6
DM-CD02-03120M817312225×0,6

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Downpipe clamps · AI01Downpipe clamps · AI01Tecfi · AI01 · 7 configurationsDescription and technical table ↓
Downpipe clamps · AI01
Tecfi series reference image.

Characteristics

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Body material: Steel. Liner: Unlined.

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Tecfi · series sheet ↗

Configuration technical table

Dimensions are in mm where stated; G identifies the listed connection. B, H and other letters retain their configuration-specific definitions: request technical review for the dimensioned drawing. Plug dimensions are not pipe diameter.

Downpipe clamps · AI01 · AI01
ReferencePlug diameter Ø (mm)Plug length L (mm)Pipe size Ø (mm)
AI 01 00 060105060
AI 01 00 080105080
AI 01 00 1001050100
AI 01 00 1251050125
AI 01 00 1401050140
AI 01 00 1601050160
AI 01 00 2001050200

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Downpipe clamps · AI02Downpipe clamps · AI02Tecfi · AI02 · 3 configurationsDescription and technical table ↓
Downpipe clamps · AI02
Tecfi series reference image.

Characteristics

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Body material: Steel. Liner: Unlined.

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Tecfi · series sheet ↗

Configuration technical table

Dimensions are in mm where stated; G identifies the listed connection. B, H and other letters retain their configuration-specific definitions: request technical review for the dimensioned drawing. Plug dimensions are not pipe diameter.

Downpipe clamps · AI02 · AI02
ReferencePlug diameter Ø (mm)Plug length L (mm)Pipe size Ø (mm)
AI 02 00 080105080
AI 02 00 1001050100
AI 02 00 1251050125

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Downpipe clamps · AI05Downpipe clamps · AI05Tecfi · AI05 · 2 configurationsDescription and technical table ↓
Downpipe clamps · AI05
Tecfi series reference image.

Characteristics

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Body material: Copper. Liner: Unlined.

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Tecfi · series sheet ↗

Configuration technical table

Dimensions are in mm where stated; G identifies the listed connection. B, H and other letters retain their configuration-specific definitions: request technical review for the dimensioned drawing. Plug dimensions are not pipe diameter.

Downpipe clamps · AI05 · AI05
ReferencePlug diameter Ø (mm)Plug length L (mm)Pipe size Ø (mm)
AI 05 00 080105080
AI 05 00 1001050100

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Downpipe clamps · AI03Downpipe clamps · AI03Tecfi · AI03 · 2 configurationsDescription and technical table ↓
Downpipe clamps · AI03
Tecfi series reference image.

Characteristics

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Body material: Steel. Liner: Unlined.

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Tecfi · series sheet ↗

Configuration technical table

Dimensions are in mm where stated; G identifies the listed connection. B, H and other letters retain their configuration-specific definitions: request technical review for the dimensioned drawing. Plug dimensions are not pipe diameter.

Downpipe clamps · AI03 · AI03
ReferencePlug diameter Ø (mm)Plug length L (mm)Pipe size L1 (mm)Pipe size L2 (mm)
AI 03 08 08010508080
AI 03 10 1001050100100

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Downpipe clamps · AI04Downpipe clamps · AI04Tecfi · AI04 · 2 configurationsDescription and technical table ↓
Downpipe clamps · AI04
Tecfi series reference image.

Characteristics

Downpipe designs may be round or square, zinc-plated, pre-painted or copper. Downpipe geometry must be distinguished from the plug diameter in the substrate.

Body material: Steel. Liner: Unlined.

For facades define exposure, stand-off distance, substrate and pipe movement. For square clamps use both section dimensions rather than an equivalent diameter.

Tecfi · series sheet ↗

Configuration technical table

Dimensions are in mm where stated; G identifies the listed connection. B, H and other letters retain their configuration-specific definitions: request technical review for the dimensioned drawing. Plug dimensions are not pipe diameter.

Downpipe clamps · AI04 · AI04
ReferencePlug diameter Ø (mm)Plug length L (mm)Pipe size L1 (mm)Pipe size L2 (mm)
AI 04 08 08010508080
AI 04 10 1001050100100

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Pipe clamp finder

Select actual outside diameter, liner, material and connection. Missing dimensions are not inferred from a part number or DN.

Request technical review or a quotation

The summary is transferred to the technical form for review and submission.

FAQ

How do lined and unlined pipe clamps differ?

A lined clamp introduces an elastomer between pipe and metal. An unlined clamp provides direct contact. A rubber insert alone does not guarantee a system noise-reduction value.

Should I select by DN or outside diameter?

Measure the actual pipe outside diameter and compare it with the clamping range. DN and nominal inch sizes must not automatically be converted into clamping diameter.

Does a heavy-duty clamp have the same capacity in every size?

No. Verification depends on clamp, screws, connection, rod, bracket, anchorage, orientation and system actions. Request data for the specific configuration.

Is a flue support clamp also a firestop collar?

No. Supporting a duct and providing a fire-resistant penetration seal are different functions with separate documentation and verification.

How do I prepare a technical enquiry?

Provide the family or sheet reference, pipe outside diameter and material, quantity, liner, connection, substrate, temperature, environment and loads or design requirements.

Related pages and documentation

Tables checked on 18 November 2026. Values refer to the listed configuration: “—” means unavailable, not zero. DN, nominal inch size and outside diameter in mm are distinct quantities. Availability and component combinations are confirmed through the technical enquiry.

Stainless pipe clamp · existing catalogue sheet · Anchors and fixings · Tecfi · clamps and fixings

Dueemme Sidol S.r.l. · Sesto San Giovanni, Milano · Supply for industrial customers and OEMs.

Dueemme Sidol
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.