Industrial fixings · Dueemme Sidol

Universal plugs

Plug deformation depends on the substrate: expansion in solid material or knotting and bearing in cavities where the design allows it. The universal designation does not remove application limits.

Tecfi RX01 · Universal plugs
Family example · Tecfi RX01

Features and selection criteria

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Designs, materials and substrates

This family contains 16 series or reference groups, with 76 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.

Documented materials

Nylon · Steel · Other polymers

Substrates mentioned in the sources

Concrete · Masonry · Perforated masonry · Aerated concrete · Plasterboard

This list describes the family and does not assign every substrate to every variant.

Information to define before selection

ParameterWhat to check
Load-bearing substrateMaterial type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size.
Fixing geometryTotal length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers.
Depth and distancesCompare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity.
Environment and exposureCheck material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment.
Loads and documentationDefine action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification.

Installation sequence to verify

  1. Identify solid material, perforated masonry or board and the space behind the hole.
  2. Select the design for its intended expansion or knotting mechanism.
  3. Match the screw and maintain the specified engagement length.
  4. Check that tightening does not crush the thin wall.

This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.

Series and technical tables

Tecfi RX01 · Universal plugsRX01Tecfi · 9 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi RX01 · Universal plugs
Series reference image · Tecfi

Series characteristics RX01

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 6–14 mm; length 32–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi RX01 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)Material
Tecfi RX 01 06 032632Nylon
Tecfi RX 01 06 045645Nylon
Tecfi RX 01 08 042842Nylon
Tecfi RX 01 08 052852Nylon
Tecfi RX 01 10 0501050Nylon
Tecfi RX 01 10 0601060Nylon
Tecfi RX 01 12 0601260Nylon
Tecfi RX 01 14 0701470Nylon
Tecfi RX 01 14 10014100Nylon

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi RX30 · Universal plugsRX30Tecfi · 4 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi RX30 · Universal plugs
Series reference image · Tecfi

Series characteristics RX30

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 6–8 mm; length 32–52 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi RX30 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)Material
Tecfi RX 30 06 032632Nylon
Tecfi RX 30 06 045645Nylon
Tecfi RX 30 08 042842Nylon
Tecfi RX 30 08 052852Nylon

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi RX00 · Universal plugsRX00Tecfi · 9 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi RX00 · Universal plugs
Series reference image · Tecfi

Series characteristics RX00

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 6–14 mm; length 32–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi RX00 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)Material
Tecfi RX 00 06 032632Nylon
Tecfi RX 00 06 045645Nylon
Tecfi RX 00 08 042842Nylon
Tecfi RX 00 08 052852Nylon
Tecfi RX 00 10 0501050Nylon
Tecfi RX 00 10 0601060Nylon
Tecfi RX 00 12 0601260Nylon
Tecfi RX 00 14 0701470Nylon
Tecfi RX 00 14 10014100Nylon

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi JC00 · Universal plugsJC00Tecfi · 5 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi JC00 · Universal plugs
Series reference image · Tecfi

Series characteristics JC00

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 5–12 mm; length 25–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi JC00 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)Material
Tecfi JC 00 05 025525Nylon
Tecfi JC 00 06 030630Nylon
Tecfi JC 00 08 040840Nylon
Tecfi JC 00 10 0501050Nylon
Tecfi JC 00 12 0601260Nylon

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi JC01 · Universal plugsJC01Tecfi · 5 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi JC01 · Universal plugs
Series reference image · Tecfi

Series characteristics JC01

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 5–12 mm; length 25–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi JC01 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)Material
Tecfi JC 01 05 025525Nylon
Tecfi JC 01 06 030630Nylon
Tecfi JC 01 08 040840Nylon
Tecfi JC 01 10 0501050Nylon
Tecfi JC 01 12 0601260Nylon

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi RX02 · Universal plugsRX02Tecfi · 6 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: countersunk head.Full description and technical table ↓
Tecfi RX02 · Universal plugs
Series reference image · Tecfi

Series characteristics RX02

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: countersunk head.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 6–10 mm; length 32–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi RX02 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)DriveMaterialFinishDiameter vite ØsLength vite Ls
Tecfi RX 02 06 032632Impronta a Croce tipo ZNylon / AcciaioZinc plated4.545
Tecfi RX 02 06 045645Impronta a Croce tipo ZNylon / AcciaioZinc plated4.555
Tecfi RX 02 08 042842Impronta a Croce tipo ZNylon / AcciaioZinc plated550
Tecfi RX 02 08 052852Impronta a Croce tipo ZNylon / AcciaioZinc plated560
Tecfi RX 02 10 0501050Impronta a Croce tipo ZNylon / AcciaioZinc plated660
Tecfi RX 02 10 0601060Impronta a Croce tipo ZNylon / AcciaioZinc plated670

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi RX03 · Universal plugsRX03Tecfi · 6 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: countersunk head.Full description and technical table ↓
Tecfi RX03 · Universal plugs
Series reference image · Tecfi

Series characteristics RX03

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: countersunk head.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 6–10 mm; length 32–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi RX03 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)DriveMaterialFinishDiameter vite ØsLength vite Ls
Tecfi RX 03 06 032632Impronta a Croce tipo ZNylon / AcciaioZinc plated4.545
Tecfi RX 03 06 045645Impronta a Croce tipo ZNylon / AcciaioZinc plated4.555
Tecfi RX 03 08 042842Impronta a Croce tipo ZNylon / AcciaioZinc plated550
Tecfi RX 03 08 052852Impronta a Croce tipo ZNylon / AcciaioZinc plated560
Tecfi RX 03 10 0501050Impronta a Croce tipo ZNylon / AcciaioZinc plated660
Tecfi RX 03 10 0601060Impronta a Croce tipo ZNylon / AcciaioZinc plated670

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi RX04 · Universal plugsRX04Tecfi · 5 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: flanged bearing, cylindrical head.Full description and technical table ↓
Tecfi RX04 · Universal plugs
Series reference image · Tecfi

Series characteristics RX04

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: flanged bearing, cylindrical head.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 6–10 mm; length 32–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi RX04 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)DriveMaterialFinishDiameter vite ØsLength vite Ls
Tecfi RX 04 06 032632Impronta a Croce tipo ZNylon / AcciaioZinc plated4.545
Tecfi RX 04 06 045645Impronta a Croce tipo ZNylon / AcciaioZinc plated4.560
Tecfi RX 04 08 052852Impronta a Croce tipo ZNylon / AcciaioZinc plated560
Tecfi RX 04 10 0501050Impronta a Croce tipo ZNylon / AcciaioZinc plated660
Tecfi RX 04 10 0601060Impronta a Croce tipo ZNylon / AcciaioZinc plated670

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi RX07 · Universal plugsRX07Tecfi · 5 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: hexagonal head.Full description and technical table ↓
Tecfi RX07 · Universal plugs
Series reference image · Tecfi

Series characteristics RX07

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: hexagonal head.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 10–14 mm; length 50–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi RX07 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)DriveMaterialFinishDiameter vite ØsLength vite Ls
Tecfi RX 07 10 0501050ChiaveNylon / AcciaioZinc plated660
Tecfi RX 07 10 0601060ChiaveNylon / AcciaioZinc plated670
Tecfi RX 07 12 0601260ChiaveNylon / AcciaioZinc plated870
Tecfi RX 07 14 0701470ChiaveNylon / AcciaioZinc plated1080
Tecfi RX 07 14 10014100ChiaveNylon / AcciaioZinc plated10120

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi JC02 · Universal plugsJC02Tecfi · 4 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: countersunk head.Full description and technical table ↓
Tecfi JC02 · Universal plugs
Series reference image · Tecfi

Series characteristics JC02

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw. Series design: countersunk head.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 5–10 mm; length 25–50 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi JC02 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)DriveMaterialFinishDiameter vite ØsLength vite Ls
Tecfi JC 02 05 025525Impronta a Croce tipo ZNylon / AcciaioZinc plated3.530
Tecfi JC 02 06 030630Impronta a Croce tipo ZNylon / AcciaioZinc plated4.540
Tecfi JC 02 08 040840Impronta a Croce tipo ZNylon / AcciaioZinc plated550
Tecfi JC 02 10 0501050Impronta a Croce tipo ZNylon / AcciaioZinc plated660

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi DQ01 · Universal plugsDQ01Tecfi · 3 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi DQ01 · Universal plugs
Series reference image · Tecfi

Series characteristics DQ01

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 6–10 mm; length 40–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi DQ01 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)Material
Tecfi DQ 01 06 040406Nylon
Tecfi DQ 01 08 050508Nylon
Tecfi DQ 01 10 0606010Nylon

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi DR01 · Universal plugsDR01Tecfi · 3 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi DR01 · Universal plugs
Series reference image · Tecfi

Series characteristics DR01

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 6–10 mm; length 40–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi DR01 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)MaterialFinishDriveDiameter vite ØsLength vite Ls
Tecfi DR 01 06 040406Nylon / AcciaioZinc platedImpronta a Croce tipo Z3.550
Tecfi DR 01 08 050508Nylon / AcciaioZinc platedImpronta a Croce tipo Z4.560
Tecfi DR 01 10 0606010Nylon / AcciaioZinc platedImpronta a Croce tipo Z680

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi DR02 · Universal plugsDR02Tecfi · 3 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi DR02 · Universal plugs
Series reference image · Tecfi

Series characteristics DR02

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 6–10 mm; length 40–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi DR02 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)MaterialFinishDriveDiameter vite ØsLength vite Ls
Tecfi DR 02 06 040406Nylon / AcciaioZinc platedImpronta a Croce tipo Z3.550
Tecfi DR 02 08 050508Nylon / AcciaioZinc platedImpronta a Croce tipo Z4.560
Tecfi DR 02 10 0606010Nylon / AcciaioZinc platedImpronta a Croce tipo Z680

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi BT01 · Universal plugsBT01Tecfi · 3 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi BT01 · Universal plugs
Series reference image · Tecfi

Series characteristics BT01

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Other polymers.

Documented series dimensions: nominal Ø 6–10 mm; length 37–61 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi BT01 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)Material
Tecfi BT 01 06 037376Polietilene HD
Tecfi BT 01 08 050508Polietilene HD
Tecfi BT 01 10 0616110Polietilene HD

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi BT02 · Universal plugsBT02Tecfi · 3 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
Tecfi BT02 · Universal plugs
Series reference image · Tecfi

Series characteristics BT02

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Other polymers, Steel.

Documented series dimensions: nominal Ø 6–10 mm; length 37–61 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi BT02 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)MaterialFinishDriveDiameter vite ØsLength vite Ls
Tecfi BT 02 06 037376Polietilene HD / AcciaioZinc platedImpronta a Croce tipo Z445
Tecfi BT 02 08 050508Polietilene HD / AcciaioZinc platedImpronta a Croce tipo Z560
Tecfi BT 02 10 0616110Polietilene HD / AcciaioZinc platedImpronta a Croce tipo Z670

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT Tassello Multi-Wand GRIPPER · Universal plugsTassello Multi-Wand GRIPPEREJOT · 3 referencesFixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.Full description and technical table ↓
EJOT Tassello Multi-Wand GRIPPER · Universal plugs
Series reference image · EJOT

Series characteristics Tassello Multi-Wand GRIPPER

Fixing using deformation of a polymer body. Behaviour in solid material or a cavity depends on the design geometry and matching screw.

Materials represented by the variants: Other polymers.

Documented series dimensions: length 32–45 mm; thread Ø 6–10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Masonry, Perforated masonry, Aerated concrete, Plasterboard. Check the application scope for the individual part.

Check wall thickness and geometry, available depth, compatible screw and deformation space. A concrete table does not describe hollow-wall behaviour.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT Tassello Multi-Wand GRIPPER · dimensional and installation characteristics
Part number and sourceThread Ø (mm)Anchor length (mm)
EJOT 96500752326.032.0
EJOT 96500752348.038.0
EJOT 965007523610.045.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Anchor finder

Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.

Request technical review or a quotation

Select a finder reference or describe the application.

The summary is transferred to the contact form for your review and submission.

FAQ

How do I select an anchor?

Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.

Does equal diameter mean equal capacity?

No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.

Do all anchors have an ETA and CE marking?

These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.

What information is needed for an enquiry?

Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.

Sources and documentation

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Tecfi · EJOT

Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.

Dueemme Sidol
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.