Sleeve anchors
An expanding sleeve transfers actions to the substrate. Bolt, nut, hook and eye versions can differ in expansion zone and installation sequence.

Features and selection criteria
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Designs, materials and substrates
This family contains 33 series or reference groups, with 211 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.
Documented materials
Steel · Stainless A2 · Stainless A4
Substrates mentioned in the sources
Concrete · Cracked concrete
This list describes the family and does not assign every substrate to every variant.
Information to define before selection
| Parameter | What to check |
|---|---|
| Load-bearing substrate | Material type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size. |
| Fixing geometry | Total length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers. |
| Depth and distances | Compare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity. |
| Environment and exposure | Check material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment. |
| Loads and documentation | Define action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification. |
Installation sequence to verify
- Identify body, thread and end form: bolt, nut, hook or eye.
- Check drill hole, depth and substrates permitted for the design.
- Insert the body in the prescribed position, with correct washer or head bearing.
- Activate expansion using the specified sequence and tightening procedure.
This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.
Series and technical tables
DSE01Tecfi · 19 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics DSE01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 8–16 mm; length 60–150 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi DSE 01 08 060 | 8 | 60 | Steel | Zinc plated | 5 | M6 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 08 080 | 8 | 80 | Steel | Zinc plated | 25 | M6 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 08 100 | 8 | 100 | Steel | Zinc plated | 45 | M6 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 08 120 | 8 | 120 | Steel | Zinc plated | 65 | M6 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 10 080 | 10 | 80 | Steel | Zinc plated | 10 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 10 100 | 10 | 100 | Steel | Zinc plated | 30 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 10 120 | 10 | 120 | Steel | Zinc plated | 50 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 10 140 | 10 | 140 | Steel | Zinc plated | 70 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 12 080 | 12 | 80 | Steel | Zinc plated | 10 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 12 100 | 12 | 100 | Steel | Zinc plated | 30 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 12 120 | 12 | 120 | Steel | Zinc plated | 50 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 12 150 | 12 | 150 | Steel | Zinc plated | 80 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 14 085 | 14 | 85 | Steel | Zinc plated | 5 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 14 100 | 14 | 100 | Steel | Zinc plated | 20 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 14 120 | 14 | 120 | Steel | Zinc plated | 40 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 14 150 | 14 | 150 | Steel | Zinc plated | 70 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 16 110 | 16 | 110 | Steel | Zinc plated | 10 | M12 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 16 130 | 16 | 130 | Steel | Zinc plated | 30 | M12 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 01 16 150 | 16 | 150 | Steel | Zinc plated | 50 | M12 | ETA-CE · EAD 330232-00-0601 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DSE11Tecfi · 12 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DSE11
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 8–16 mm; length 80–150 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi DSE 11 08 080 | 8 | 80 | Steel | Zinc plated | 25 | M6 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 10 080 | 10 | 80 | Steel | Zinc plated | 10 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 10 100 | 10 | 100 | Steel | Zinc plated | 30 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 10 120 | 10 | 120 | Steel | Zinc plated | 50 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 10 140 | 10 | 140 | Steel | Zinc plated | 70 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 12 100 | 12 | 100 | Steel | Zinc plated | 30 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 12 120 | 12 | 120 | Steel | Zinc plated | 50 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 12 150 | 12 | 150 | Steel | Zinc plated | 80 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 14 100 | 14 | 100 | Steel | Zinc plated | 20 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 14 120 | 14 | 120 | Steel | Zinc plated | 40 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 11 16 130 | 16 | 130 | Steel | Zinc plated | 30 | M12 | — |
| Tecfi DSE 11 16 150 | 16 | 150 | Steel | Zinc plated | 50 | M12 | — |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DSE07Tecfi · 19 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DSE07
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 8–16 mm; length 45–135 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi DSE 07 08 045 | 8 | 45 | Steel | Zinc plated | 5 | M6 | — |
| Tecfi DSE 07 08 060 | 8 | 60 | Steel | Zinc plated | 5 | M6 | — |
| Tecfi DSE 07 08 080 | 8 | 80 | Steel | Zinc plated | 25 | M6 | — |
| Tecfi DSE 07 08 100 | 8 | 100 | Steel | Zinc plated | 45 | M6 | — |
| Tecfi DSE 07 08 120 | 8 | 120 | Steel | Zinc plated | 65 | M6 | — |
| Tecfi DSE 07 10 065 | 10 | 65 | Steel | Zinc plated | 15 | M8 | — |
| Tecfi DSE 07 10 085 | 10 | 85 | Steel | Zinc plated | 15 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 10 105 | 10 | 105 | Steel | Zinc plated | 35 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 10 125 | 10 | 125 | Steel | Zinc plated | 55 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 12 070 | 12 | 70 | Steel | Zinc plated | 20 | M10 | — |
| Tecfi DSE 07 12 080 | 12 | 80 | Steel | Zinc plated | 10 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 12 110 | 12 | 110 | Steel | Zinc plated | 40 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 12 130 | 12 | 130 | Steel | Zinc plated | 60 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 14 075 | 14 | 75 | Steel | Zinc plated | 15 | M10 | — |
| Tecfi DSE 07 14 105 | 14 | 105 | Steel | Zinc plated | 25 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 14 125 | 14 | 125 | Steel | Zinc plated | 45 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 07 16 080 | 16 | 80 | Steel | Zinc plated | 20 | M12 | — |
| Tecfi DSE 07 16 115 | 16 | 115 | Steel | Zinc plated | 15 | M12 | — |
| Tecfi DSE 07 16 135 | 16 | 135 | Steel | Zinc plated | 35 | M12 | — |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DSE10Tecfi · 11 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DSE10
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–14 mm; length 60–120 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi DSE 10 10 060 | 10 | 60 | Steel | Zinc plated | 10 | M8 | — |
| Tecfi DSE 10 10 080 | 10 | 80 | Steel | Zinc plated | 10 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 10 100 | 10 | 100 | Steel | Zinc plated | 30 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 10 120 | 10 | 120 | Steel | Zinc plated | 50 | M8 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 12 060 | 12 | 60 | Steel | Zinc plated | 10 | M10 | — |
| Tecfi DSE 10 12 080 | 12 | 80 | Steel | Zinc plated | 10 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 12 100 | 12 | 100 | Steel | Zinc plated | 30 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 12 120 | 12 | 120 | Steel | Zinc plated | 50 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 14 085 | 14 | 85 | Steel | Zinc plated | 5 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 14 100 | 14 | 100 | Steel | Zinc plated | 20 | M10 | ETA-CE · EAD 330232-00-0601 |
| Tecfi DSE 10 14 120 | 14 | 120 | Steel | Zinc plated | 40 | M10 | ETA-CE · EAD 330232-00-0601 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DS02Tecfi · 6 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DS02
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–12 mm; length 65–130 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M |
|---|---|---|---|---|---|---|
| Tecfi DS 02 10 060 | 10 | 65 | Steel | Zinc plated | 5 | M8 |
| Tecfi DS 02 10 080 | 10 | 85 | Steel | Zinc plated | 25 | M8 |
| Tecfi DS 02 10 100 | 10 | 105 | Steel | Zinc plated | 45 | M8 |
| Tecfi DS 02 12 070 | 12 | 80 | Steel | Zinc plated | 10 | M10 |
| Tecfi DS 02 12 100 | 12 | 110 | Steel | Zinc plated | 40 | M10 |
| Tecfi DS 02 12 120 | 12 | 130 | Steel | Zinc plated | 60 | M10 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DS08Tecfi · 2 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DS08
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Stainless A2.
Documented series dimensions: nominal Ø 10 mm; length 65–105 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M |
|---|---|---|---|---|---|---|
| Tecfi DS 08 10 060 | 10 | 65 | Acciaio / Acciaio Inox A2 | Zinc plated | 5 | M8 |
| Tecfi DS 08 10 100 | 10 | 105 | Acciaio / Acciaio Inox A2 | Zinc plated | 45 | M8 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DS03Tecfi · 2 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: countersunk head.Full description and technical table ↓

Series characteristics DS03
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: countersunk head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10 mm; length 90–110 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M |
|---|---|---|---|---|---|---|
| Tecfi DS 03 10 080 | 10 | 90 | Steel | Zinc plated | 30 | M8 |
| Tecfi DS 03 10 100 | 10 | 110 | Steel | Zinc plated | 50 | M8 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
LZ01Tecfi · 24 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics LZ01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 8–16 mm; length 45–150 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M |
|---|---|---|---|---|---|---|
| Tecfi LZ 01 08 045 | 8 | 45 | Steel | Zinc plated | 5 | M6 |
| Tecfi LZ 01 08 060 | 8 | 60 | Steel | Zinc plated | 5 | M6 |
| Tecfi LZ 01 08 070 | 8 | 70 | Steel | Zinc plated | 15 | M6 |
| Tecfi LZ 01 08 080 | 8 | 80 | Steel | Zinc plated | 25 | M6 |
| Tecfi LZ 01 08 100 | 8 | 100 | Steel | Zinc plated | 45 | M6 |
| Tecfi LZ 01 08 120 | 8 | 120 | Steel | Zinc plated | 65 | M6 |
| Tecfi LZ 01 10 065 | 10 | 65 | Steel | Zinc plated | 15 | M8 |
| Tecfi LZ 01 10 080 | 10 | 80 | Steel | Zinc plated | 10 | M8 |
| Tecfi LZ 01 10 100 | 10 | 100 | Steel | Zinc plated | 30 | M8 |
| Tecfi LZ 01 10 140 | 10 | 140 | Steel | Zinc plated | 70 | M8 |
| Tecfi LZ 01 12 065 | 12 | 65 | Steel | Zinc plated | 15 | M10 |
| Tecfi LZ 01 12 075 | 12 | 75 | Steel | Zinc plated | 15 | M10 |
| Tecfi LZ 01 12 100 | 12 | 100 | Steel | Zinc plated | 30 | M10 |
| Tecfi LZ 01 12 120 | 12 | 120 | Steel | Zinc plated | 50 | M10 |
| Tecfi LZ 01 12 150 | 12 | 150 | Steel | Zinc plated | 80 | M10 |
| Tecfi LZ 01 14 075 | 14 | 75 | Steel | Zinc plated | 15 | M10 |
| Tecfi LZ 01 14 085 | 14 | 85 | Steel | Zinc plated | 5 | M10 |
| Tecfi LZ 01 14 100 | 14 | 100 | Steel | Zinc plated | 20 | M10 |
| Tecfi LZ 01 14 120 | 14 | 120 | Steel | Zinc plated | 40 | M10 |
| Tecfi LZ 01 14 150 | 14 | 150 | Steel | Zinc plated | 70 | M10 |
| Tecfi LZ 01 16 075 | 16 | 75 | Steel | Zinc plated | 15 | M12 |
| Tecfi LZ 01 16 110 | 16 | 110 | Steel | Zinc plated | 10 | M12 |
| Tecfi LZ 01 16 130 | 16 | 130 | Steel | Zinc plated | 30 | M12 |
| Tecfi LZ 01 16 150 | 16 | 150 | Steel | Zinc plated | 50 | M12 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
LZ51Tecfi · 19 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics LZ51
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Stainless A2.
Documented series dimensions: nominal Ø 8–16 mm; length 60–130 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Fixture thickness (mm) tfix | Misura vite M |
|---|---|---|---|---|---|
| Tecfi LZ 51 08 060 | 8 | 60 | Acciaio Inox A2 | 5 | M6 |
| Tecfi LZ 51 08 075 | 8 | 75 | Acciaio Inox A2 | 20 | M6 |
| Tecfi LZ 51 08 095 | 8 | 95 | Acciaio Inox A2 | 40 | M6 |
| Tecfi LZ 51 08 115 | 8 | 115 | Acciaio Inox A2 | 60 | M6 |
| Tecfi LZ 51 10 065 | 10 | 65 | Acciaio Inox A2 | 15 | M8 |
| Tecfi LZ 51 10 080 | 10 | 80 | Acciaio Inox A2 | 10 | M8 |
| Tecfi LZ 51 10 100 | 10 | 100 | Acciaio Inox A2 | 30 | M8 |
| Tecfi LZ 51 10 120 | 10 | 120 | Acciaio Inox A2 | 50 | M8 |
| Tecfi LZ 51 12 065 | 12 | 65 | Acciaio Inox A2 | 15 | M10 |
| Tecfi LZ 51 12 080 | 12 | 80 | Acciaio Inox A2 | 10 | M10 |
| Tecfi LZ 51 12 100 | 12 | 100 | Acciaio Inox A2 | 30 | M10 |
| Tecfi LZ 51 12 120 | 12 | 120 | Acciaio Inox A2 | 50 | M10 |
| Tecfi LZ 51 14 075 | 14 | 75 | Acciaio Inox A2 | 15 | M10 |
| Tecfi LZ 51 14 100 | 14 | 100 | Acciaio Inox A2 | 20 | M10 |
| Tecfi LZ 51 14 110 | 14 | 110 | Acciaio Inox A2 | 30 | M10 |
| Tecfi LZ 51 14 130 | 14 | 130 | Acciaio Inox A2 | 50 | M10 |
| Tecfi LZ 51 16 075 | 16 | 75 | Acciaio Inox A2 | 15 | M12 |
| Tecfi LZ 51 16 110 | 16 | 110 | Acciaio Inox A2 | 10 | M12 |
| Tecfi LZ 51 16 130 | 16 | 130 | Acciaio Inox A2 | 30 | M12 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DXE00Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DXE00
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|
| Tecfi DXE 00 10 045 | 10 | 45 | Steel | Zinc plated | M6 | ETA-CE |
| Tecfi DXE 00 12 050 | 12 | 50 | Steel | Zinc plated | M8 | ETA-CE |
| Tecfi DXE 00 15 060 | 15 | 60 | Steel | Zinc plated | M10 | ETA-CE |
| Tecfi DXE 00 18 075 | 18 | 75 | Steel | Zinc plated | M12 | ETA-CE |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DXE01Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics DXE01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi DXE 01 10 050 | 10 | 45 | Steel | Zinc plated | M6 | 50 | ETA-CE |
| Tecfi DXE 01 12 060 | 12 | 50 | Steel | Zinc plated | M8 | 60 | ETA-CE |
| Tecfi DXE 01 15 080 | 15 | 60 | Steel | Zinc plated | M10 | 80 | ETA-CE |
| Tecfi DXE 01 18 100 | 18 | 75 | Steel | Zinc plated | M12 | 100 | ETA-CE |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DXE03Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DXE03
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi DXE 03 10 060 | 10 | 45 | Steel | Zinc plated | M6 | 60 | ETA-CE |
| Tecfi DXE 03 12 075 | 12 | 50 | Steel | Zinc plated | M8 | 75 | ETA-CE |
| Tecfi DXE 03 15 095 | 15 | 60 | Steel | Zinc plated | M10 | 95 | ETA-CE |
| Tecfi DXE 03 18 120 | 18 | 75 | Steel | Zinc plated | M12 | 120 | ETA-CE |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DXE04Tecfi · 7 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DXE04
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–15 mm; length 50–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi DXE 04 12 060 | 12 | 50 | Steel | Zinc plated | M8 | 65 |
| Tecfi DXE 04 12 080 | 12 | 50 | Steel | Zinc plated | M8 | 85 |
| Tecfi DXE 04 12 100 | 12 | 50 | Steel | Zinc plated | M8 | 105 |
| Tecfi DXE 04 12 120 | 12 | 50 | Steel | Zinc plated | M8 | 125 |
| Tecfi DXE 04 15 080 | 15 | 60 | Steel | Zinc plated | M10 | 85 |
| Tecfi DXE 04 15 100 | 15 | 60 | Steel | Zinc plated | M10 | 110 |
| Tecfi DXE 04 15 120 | 15 | 60 | Steel | Zinc plated | M10 | 130 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX00Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DX00
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M |
|---|---|---|---|---|---|
| Tecfi DX 00 10 045 | 10 | 45 | Steel | Zinc plated | M6 |
| Tecfi DX 00 12 050 | 12 | 50 | Steel | Zinc plated | M8 |
| Tecfi DX 00 15 060 | 15 | 60 | Steel | Zinc plated | M10 |
| Tecfi DX 00 18 075 | 18 | 75 | Steel | Zinc plated | M12 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX01Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics DX01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi DX 01 10 045 | 10 | 45 | Steel | Zinc plated | M6 | 50 |
| Tecfi DX 01 12 050 | 12 | 50 | Steel | Zinc plated | M8 | 60 |
| Tecfi DX 01 15 060 | 15 | 60 | Steel | Zinc plated | M10 | 80 |
| Tecfi DX 01 18 075 | 18 | 75 | Steel | Zinc plated | M12 | 90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX01spTecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics DX01sp
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 70–105 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi DX 01 10 070 | 10 | 70 | Steel | Zinc plated | M6 | 75 |
| Tecfi DX 01 12 075 | 12 | 75 | Steel | Zinc plated | M8 | 80 |
| Tecfi DX 01 15 085 | 15 | 85 | Steel | Zinc plated | M10 | 90 |
| Tecfi DX 01 18 105 | 18 | 105 | Steel | Zinc plated | M12 | 110 |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX70Tecfi · 3 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DX70
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Stainless A4.
Documented series dimensions: nominal Ø 12–18 mm; length 50–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Misura vite M |
|---|---|---|---|---|
| Tecfi DX 70 12 050 | 12 | 50 | Acciaio Inox A4 | M8 |
| Tecfi DX 70 15 060 | 15 | 60 | Acciaio Inox A4 | M10 |
| Tecfi DX 70 18 075 | 18 | 75 | Acciaio Inox A4 | M12 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX71Tecfi · 3 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics DX71
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Stainless A4.
Documented series dimensions: nominal Ø 10–15 mm; length 45–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|
| Tecfi DX 71 10 045 | 10 | 45 | Acciaio Inox A4 | M6 | 50 |
| Tecfi DX 71 12 050 | 12 | 50 | Acciaio Inox A4 | M8 | 60 |
| Tecfi DX 71 15 060 | 15 | 60 | Acciaio Inox A4 | M10 | 80 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX07Tecfi · 2 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DX07
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–15 mm; length 50–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi DX 07 12 050 | 12 | 50 | Steel | Zinc plated | M8 | 65 |
| Tecfi DX 07 15 060 | 15 | 60 | Steel | Zinc plated | M10 | 65 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX04Tecfi · 1 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DX04
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12 mm; length 80 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M |
|---|---|---|---|---|---|
| Tecfi DX 04 12 080 | 12 | 80 | Steel | Zinc plated | M8 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX05Tecfi · 1 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DX05
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Stainless A2.
Documented series dimensions: nominal Ø 12 mm; length 80 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M |
|---|---|---|---|---|---|
| Tecfi DX 05 12 080 | 12 | 80 | Acciaio / Acciaio Inox A2 | Zinc plated | M8 |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX03Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hook end.Full description and technical table ↓

Series characteristics DX03
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hook end.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi DX 03 10 045 | 10 | 45 | Steel | Zinc plated | M6 | 55 |
| Tecfi DX 03 12 050 | 12 | 50 | Steel | Zinc plated | M8 | 65 |
| Tecfi DX 03 15 060 | 15 | 60 | Steel | Zinc plated | M10 | 81 |
| Tecfi DX 03 18 075 | 18 | 75 | Steel | Zinc plated | M12 | 98 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX02Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: eye end.Full description and technical table ↓

Series characteristics DX02
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: eye end.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Eye internal Ø (mm) | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi DX 02 10 045 | 10 | 45 | Steel | Zinc plated | 10 | M6 | 55 |
| Tecfi DX 02 12 050 | 12 | 50 | Steel | Zinc plated | 11.5 | M8 | 65 |
| Tecfi DX 02 15 060 | 15 | 60 | Steel | Zinc plated | 14 | M10 | 81 |
| Tecfi DX 02 18 075 | 18 | 75 | Steel | Zinc plated | 17 | M12 | 98 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DX06Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics DX06
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M |
|---|---|---|---|---|---|
| Tecfi DX 06 10 045 | 10 | 45 | Steel | Zinc plated | M6 |
| Tecfi DX 06 12 050 | 12 | 50 | Steel | Zinc plated | M8 |
| Tecfi DX 06 15 060 | 15 | 60 | Steel | Zinc plated | M10 |
| Tecfi DX 06 18 075 | 18 | 75 | Steel | Zinc plated | M12 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
CP01Tecfi · 5 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics CP01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–24 mm; length 45–95 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M |
|---|---|---|---|---|---|
| Tecfi CP 01 12 045 | 12 | 45 | Steel | Zinc plated | M6 |
| Tecfi CP 01 14 050 | 14 | 50 | Steel | Zinc plated | M8 |
| Tecfi CP 01 16 060 | 16 | 60 | Steel | Zinc plated | M10 |
| Tecfi CP 01 20 075 | 20 | 75 | Steel | Zinc plated | M12 |
| Tecfi CP 01 24 095 | 24 | 95 | Steel | Zinc plated | M16 |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
CQ01Tecfi · 5 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.Full description and technical table ↓

Series characteristics CQ01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–24 mm; length 45–95 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls | Intestazione codici |
|---|---|---|---|---|---|---|---|
| Tecfi CQ 01 12 045 | 12 | 45 | Steel | Zinc plated | M6 | 50 | SW: 10 |
| Tecfi CQ 01 14 050 | 14 | 50 | Steel | Zinc plated | M8 | 60 | SW: 13 |
| Tecfi CQ 01 16 060 | 16 | 60 | Steel | Zinc plated | M10 | 80 | SW: 17 |
| Tecfi CQ 01 20 075 | 20 | 75 | Steel | Zinc plated | M12 | 90 | SW: 19 |
| Tecfi CQ 01 24 095 | 24 | 95 | Steel | Zinc plated | M16 | 110 | SW: 24 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
CS01Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hook end.Full description and technical table ↓

Series characteristics CS01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: hook end.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–20 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi CS 01 12 045 | 12 | 45 | Steel | Zinc plated | M6 | 55 |
| Tecfi CS 01 14 050 | 14 | 50 | Steel | Zinc plated | M8 | 65 |
| Tecfi CS 01 16 060 | 16 | 60 | Steel | Zinc plated | M10 | 81 |
| Tecfi CS 01 20 075 | 20 | 75 | Steel | Zinc plated | M12 | 98 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
CT01Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: eye end.Full description and technical table ↓

Series characteristics CT01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: eye end.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–20 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Eye internal Ø (mm) | Misura vite M | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi CT 01 12 045 | 12 | 45 | Steel | Zinc plated | 10 | M6 | 55 |
| Tecfi CT 01 14 050 | 14 | 50 | Steel | Zinc plated | 11.5 | M8 | 65 |
| Tecfi CT 01 16 060 | 16 | 60 | Steel | Zinc plated | 14 | M10 | 81 |
| Tecfi CT 01 20 075 | 20 | 75 | Steel | Zinc plated | 17 | M12 | 98 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
CR01Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics CR01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–20 mm; length 45–75 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Misura vite M | Pz Imballo |
|---|---|---|---|---|---|---|
| Tecfi CR 01 12 045 | 12 | 45 | Steel | Zinc plated | M6 | SW: 10 |
| Tecfi CR 01 14 050 | 14 | 50 | Steel | Zinc plated | M8 | SW: 13 |
| Tecfi CR 01 16 060 | 16 | 60 | Steel | Zinc plated | M10 | SW: 17 |
| Tecfi CR 01 20 075 | 20 | 75 | Steel | Zinc plated | M12 | SW: 19 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
AW01Tecfi · 9 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: flanged bearing, flange nut.Full description and technical table ↓

Series characteristics AW01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: flanged bearing, flange nut.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 8–16 mm; length 50–147 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M |
|---|---|---|---|---|---|---|
| Tecfi AW 01 08 065 | 8 | 65 | Steel | Zinc plated | 10 | M6 |
| Tecfi AW 01 10 050 | 10 | 50 | Steel | Zinc plated | 10 | M8 |
| Tecfi AW 01 10 077 | 10 | 77 | Steel | Zinc plated | 15 | M8 |
| Tecfi AW 01 10 097 | 10 | 97 | Steel | Zinc plated | 20 | M8 |
| Tecfi AW 01 12 075 | 12 | 75 | Steel | Zinc plated | 10 | M10 |
| Tecfi AW 01 12 099 | 12 | 99 | Steel | Zinc plated | 20 | M10 |
| Tecfi AW 01 12 129 | 12 | 129 | Steel | Zinc plated | 30 | M10 |
| Tecfi AW 01 16 111 | 16 | 111 | Steel | Zinc plated | 20 | M12 |
| Tecfi AW 01 16 147 | 16 | 147 | Steel | Zinc plated | 30 | M12 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
FR01Tecfi · 8 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics FR01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 72–182 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi FR 01 08 072 | 8 | 72 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 5 | 85 |
| Tecfi FR 01 08 092 | 8 | 92 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 5 | 105 |
| Tecfi FR 01 10 072 | 10 | 72 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 6 | 88 |
| Tecfi FR 01 10 092 | 10 | 92 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 6 | 108 |
| Tecfi FR 01 10 112 | 10 | 112 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 6 | 128 |
| Tecfi FR 01 10 132 | 10 | 132 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 6 | 148 |
| Tecfi FR 01 10 152 | 10 | 152 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 6 | 168 |
| Tecfi FR 01 10 182 | 10 | 182 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 6 | 195 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
FR02Tecfi · 4 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.Full description and technical table ↓

Series characteristics FR02
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 8 mm; length 72–132 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi FR 02 08 072 | 8 | 72 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 5 | 85 |
| Tecfi FR 02 08 092 | 8 | 92 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 5 | 105 |
| Tecfi FR 02 08 112 | 8 | 112 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 5 | 125 |
| Tecfi FR 02 08 132 | 8 | 132 | Impronta combinata Taglio / Croce tipo Z | Steel | Zinc plated | 5 | 145 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
HN01Tecfi · 1 referencesMetal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: eye end.Full description and technical table ↓

Series characteristics HN01
Metal sleeve-expansion system. Mechanism activation establishes substrate contact according to the design geometry and procedure. Series design: eye end.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 6 mm; length 60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare anchor body and drill hole without confusing either with the bolt thread. For masonry or perforated materials, use only the applications declared in the design-specific sheet.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø (mm) | Material | Finish | Diameter Ø (mm) | Length L (mm) |
|---|---|---|---|---|---|
| Tecfi HN 01 06 060 | 6 | Steel | Zinc plated | 6 | 60 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Anchor finder
Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.
Request technical review or a quotation
Select a finder reference or describe the application.
FAQ
How do I select an anchor?
Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.
Does equal diameter mean equal capacity?
No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.
Do all anchors have an ETA and CE marking?
These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.
What information is needed for an enquiry?
Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.
Sources and documentation
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.