Industrial fixings · Dueemme Sidol

Self-drilling plasterboard fixings

Self-drilling designs screw into the board and receive a dedicated screw. Anchor material and thread geometry must suit the board type and thickness.

Tecfi HE00 · Self-drilling plasterboard fixings
Family example · Tecfi HE00

Features and selection criteria

Check whether pre-drilling is required and which boards are permitted. Suspended and overhead loads require application-specific verification; do not transfer values from a different board.

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Designs, materials and substrates

This family contains 4 series or reference groups, with 6 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.

Documented materials

Zinc alloy · Steel · Nylon

Substrates mentioned in the sources

Check the reference documentation.

This list describes the family and does not assign every substrate to every variant.

Information to define before selection

ParameterWhat to check
Load-bearing substrateMaterial type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size.
Fixing geometryTotal length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers.
Depth and distancesCompare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity.
Environment and exposureCheck material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment.
Loads and documentationDefine action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification.

Installation sequence to verify

  1. Identify board type and any framing or services behind it.
  2. Check whether the design requires a pilot hole.
  3. Screw in the body without damaging the board facing.
  4. Use the matching screw and respect the declared application limits.

This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.

Series and technical tables

Tecfi HE00 · Self-drilling plasterboard fixingsHE00Tecfi · 2 referencesThreaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board.Full description and technical table ↓
Tecfi HE00 · Self-drilling plasterboard fixings
Series reference image · Tecfi

Series characteristics HE00

Threaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board.

Materials represented by the variants: Zinc alloy.

Documented series dimensions: nominal Ø 13–15 mm; length 29–34 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check whether pre-drilling is required and which boards are permitted. Suspended and overhead loads require application-specific verification; do not transfer values from a different board.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HE00 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)Material
Tecfi HE 00 13 0343413Lega di zinco
Tecfi HE 00 15 0292915Lega di zinco

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HE01 · Self-drilling plasterboard fixingsHE01Tecfi · 2 referencesThreaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board. Series design: flanged bearing, cylindrical head.Full description and technical table ↓
Tecfi HE01 · Self-drilling plasterboard fixings
Series reference image · Tecfi

Series characteristics HE01

Threaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board. Series design: flanged bearing, cylindrical head.

Materials represented by the variants: Steel, Zinc alloy.

Documented series dimensions: nominal Ø 13–15 mm; length 29–34 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check whether pre-drilling is required and which boards are permitted. Suspended and overhead loads require application-specific verification; do not transfer values from a different board.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HE01 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)MaterialFinishDriveDiameter vite ØsLength vite LsTfix (spess. fissabile) MAX
Tecfi HE 01 13 0343413Lega di zinco / AcciaioZinc platedImpronta a Croce tipo Z4.55030 -
Tecfi HE 01 15 0292915Lega di zinco / AcciaioZinc platedImpronta a Croce tipo Z54020 -

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HF00 · Self-drilling plasterboard fixingsHF00Tecfi · 1 referencesThreaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board.Full description and technical table ↓
Tecfi HF00 · Self-drilling plasterboard fixings
Series reference image · Tecfi

Series characteristics HF00

Threaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 15 mm; length 32 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check whether pre-drilling is required and which boards are permitted. Suspended and overhead loads require application-specific verification; do not transfer values from a different board.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HF00 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)Material
Tecfi HF 00 15 0323215Nylon

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HF01 · Self-drilling plasterboard fixingsHF01Tecfi · 1 referencesThreaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board. Series design: flanged bearing, cylindrical head.Full description and technical table ↓
Tecfi HF01 · Self-drilling plasterboard fixings
Series reference image · Tecfi

Series characteristics HF01

Threaded body inserted into plasterboard and used with a matching screw. Body geometry governs engagement in the board. Series design: flanged bearing, cylindrical head.

Materials represented by the variants: Nylon, Steel.

Documented series dimensions: nominal Ø 15 mm; length 32 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Check whether pre-drilling is required and which boards are permitted. Suspended and overhead loads require application-specific verification; do not transfer values from a different board.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HF01 · dimensional and installation characteristics
Part number and sourceAnchor length (mm)Anchor body Ø (mm)MaterialFinishDriveDiameter vite ØsLength vite LsTfix (spess. fissabile) MINTfix (spess. fissabile) MAX
Tecfi HF 01 15 0323215Nylon / AcciaioZinc platedImpronta a Croce tipo Z4.5351015 -

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Anchor finder

Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.

Request technical review or a quotation

Select a finder reference or describe the application.

The summary is transferred to the contact form for your review and submission.

FAQ

How do I select an anchor?

Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.

Does equal diameter mean equal capacity?

No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.

Do all anchors have an ETA and CE marking?

These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.

What information is needed for an enquiry?

Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.

Sources and documentation

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Tecfi · EJOT

Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.

Dueemme Sidol
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.