Heavy-duty and undercut anchors
Heavy-duty and undercut families use specific load-transfer mechanisms. The commercial designation does not assign a common load capacity to the family.

Features and selection criteria
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Designs, materials and substrates
This family contains 11 series or reference groups, with 115 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.
Documented materials
Steel · Stainless A4
Substrates mentioned in the sources
Concrete · Cracked concrete
This list describes the family and does not assign every substrate to every variant.
Information to define before selection
| Parameter | What to check |
|---|---|
| Load-bearing substrate | Material type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size. |
| Fixing geometry | Total length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers. |
| Depth and distances | Compare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity. |
| Environment and exposure | Check material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment. |
| Loads and documentation | Define action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification. |
Installation sequence to verify
- Identify the exact system configuration in the ETA and design.
- Drill and form any undercut using the specified equipment.
- Check depth, cleaning and correct mechanism activation.
- Check tightening and the manufacturer’s verification criteria.
This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.
Series and technical tables
HVE01Tecfi · 20 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: hexagonal head.Full description and technical table ↓

Series characteristics HVE01
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–24 mm; length 70–220 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi HVE 01 10 070 | 10 | 70 | Steel | Zinc plated | 5 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 10 080 | 10 | 80 | Steel | Zinc plated | 15 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 10 100 | 10 | 100 | Steel | Zinc plated | 35 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 10 120 | 10 | 120 | Steel | Zinc plated | 55 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 12 080 | 12 | 80 | Steel | Zinc plated | 10 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 12 100 | 12 | 100 | Steel | Zinc plated | 30 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 12 120 | 12 | 120 | Steel | Zinc plated | 50 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 12 140 | 12 | 140 | Steel | Zinc plated | 70 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 16 100 | 16 | 100 | Steel | Zinc plated | 20 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 16 120 | 16 | 120 | Steel | Zinc plated | 40 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 16 140 | 16 | 140 | Steel | Zinc plated | 60 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 16 160 | 16 | 160 | Steel | Zinc plated | 80 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 18 120 | 18 | 120 | Steel | Zinc plated | 20 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 18 150 | 18 | 150 | Steel | Zinc plated | 50 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 18 170 | 18 | 170 | Steel | Zinc plated | 70 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 18 200 | 18 | 200 | Steel | Zinc plated | 100 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 24 140 | 24 | 140 | Steel | Zinc plated | 20 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 24 170 | 24 | 170 | Steel | Zinc plated | 50 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 24 200 | 24 | 200 | Steel | Zinc plated | 80 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 01 24 220 | 24 | 220 | Steel | Zinc plated | 100 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
HVE02Tecfi · 20 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.Full description and technical table ↓

Series characteristics HVE02
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–24 mm; length 70–220 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi HVE 02 10 070 | 10 | 70 | Steel | Zinc plated | 5 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 10 080 | 10 | 80 | Steel | Zinc plated | 15 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 10 100 | 10 | 100 | Steel | Zinc plated | 35 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 10 120 | 10 | 120 | Steel | Zinc plated | 55 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 12 080 | 12 | 80 | Steel | Zinc plated | 10 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 12 100 | 12 | 100 | Steel | Zinc plated | 30 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 12 120 | 12 | 120 | Steel | Zinc plated | 50 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 12 140 | 12 | 140 | Steel | Zinc plated | 70 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 16 100 | 16 | 100 | Steel | Zinc plated | 20 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 16 120 | 16 | 120 | Steel | Zinc plated | 40 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 16 140 | 16 | 140 | Steel | Zinc plated | 60 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 16 160 | 16 | 160 | Steel | Zinc plated | 80 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 18 120 | 18 | 120 | Steel | Zinc plated | 20 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 18 150 | 18 | 150 | Steel | Zinc plated | 50 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 18 170 | 18 | 170 | Steel | Zinc plated | 70 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 18 200 | 18 | 200 | Steel | Zinc plated | 100 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 24 140 | 24 | 140 | Steel | Zinc plated | 20 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 24 170 | 24 | 170 | Steel | Zinc plated | 50 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 24 200 | 24 | 200 | Steel | Zinc plated | 80 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 02 24 220 | 24 | 220 | Steel | Zinc plated | 100 | M16 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
HVE03Tecfi · 10 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: countersunk head.Full description and technical table ↓

Series characteristics HVE03
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: countersunk head.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 10–18 mm; length 85–140 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi HVE 03 10 085 | 10 | 85 | Steel | Zinc plated | 20 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 10 105 | 10 | 105 | Steel | Zinc plated | 40 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 10 125 | 10 | 125 | Steel | Zinc plated | 60 | M6 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 12 085 | 12 | 85 | Steel | Zinc plated | 15 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 12 105 | 12 | 105 | Steel | Zinc plated | 35 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 12 125 | 12 | 125 | Steel | Zinc plated | 55 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 16 110 | 16 | 110 | Steel | Zinc plated | 30 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 16 130 | 16 | 130 | Steel | Zinc plated | 50 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 18 120 | 18 | 120 | Steel | Zinc plated | 20 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 03 18 140 | 18 | 140 | Steel | Zinc plated | 40 | M12 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
HVE04Tecfi · 5 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics HVE04
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: six-lobe drive.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 12–16 mm; length 80–120 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix | Misura vite M | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi HVE 04 12 080 | 12 | 80 | Steel | Zinc plated | 10 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 04 12 100 | 12 | 100 | Steel | Zinc plated | 30 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 04 12 120 | 12 | 120 | Steel | Zinc plated | 50 | M8 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 04 16 100 | 16 | 100 | Steel | Zinc plated | 20 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
| Tecfi HVE 04 16 120 | 16 | 120 | Steel | Zinc plated | 40 | M10 | ETA-CE · EAD 330232-00-0601 · R049 R120 (TR 020) R049 · Sisma / Seismic |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Tassello di sicurezza LIEBIG® SKEJOT · 10 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.Full description and technical table ↓

Series characteristics Tassello di sicurezza LIEBIG® SK
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.
Materials represented by the variants: Steel.
Documented series dimensions: length 70–160 mm; thread Ø 10–25 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal size | Length (mm) | Thread Ø (mm) | Hole depth ≤ (mm), source wording | Drill bit Ø (mm) | Fixture thickness B ≥ (mm) | Fixture thickness (mm) | ø cone d k ≥ | Height cone k | HEX |
|---|---|---|---|---|---|---|---|---|---|---|
| EJOT 9650045415 | M6 | 70.0 | 10.0 | 60.0 | 10.0 | 15.0 | 15.0 | 20.0 | 5.5 | 50.0 |
| EJOT 9650045440 | M6 | 95.0 | 10.0 | 60.0 | — | 40.0 | — | 20.0 | 5.5 | 50.0 |
| EJOT 9652055415 | M8 | 85.0 | 12.0 | 70.0 | 12.0 | 15.0 | 15.0 | 20.0 | 6.5 | 25.0 |
| EJOT 9652055440 | M8 | 110.0 | 12.0 | 70.0 | 12.0 | 40.0 | 40.0 | 24.0 | 6.5 | 25.0 |
| EJOT 9655070415 | — | 100.0 | 15.0 | 85.0 | 15.0 | 15.0 | 15.0 | — | — | — |
| EJOT 9655070440 | — | 120.0 | 15.0 | 85.0 | 15.0 | 40.0 | 40.0 | — | — | — |
| EJOT 9650080415 | — | 110.0 | 20.0 | 100.0 | 20.0 | 15.0 | 15.0 | — | — | — |
| EJOT 9650080440 | — | 135.0 | 20.0 | 100.0 | 20.0 | 40.0 | 40.0 | — | — | — |
| EJOT 9655100415 | — | 135.0 | 25.0 | 125.0 | 25.0 | 15.0 | 15.0 | — | — | — |
| EJOT 9655100440 | — | 160.0 | 25.0 | 125.0 | 25.0 | 40.0 | 40.0 | — | — | — |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Tassello di sicurezza LIEBIG® SEJOT · 15 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.Full description and technical table ↓

Series characteristics Tassello di sicurezza LIEBIG® S
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.
Materials represented by the variants: Steel.
Documented series dimensions: length 70–180 mm; thread Ø 10–25 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Length (mm) | Thread Ø (mm) | Hole depth ≤ (mm), source wording | Drill bit Ø (mm) | Fixture thickness B ≥ (mm) | Fixture thickness (mm) |
|---|---|---|---|---|---|---|
| EJOT 9650045105 | 70.0 | 10.0 | 60.0 | 10.0 | 5.0 | 5.0 |
| EJOT 9650045115 | 80.0 | 10.0 | 60.0 | 10.0 | 15.0 | 15.0 |
| EJOT 9650045140 | 105.0 | 10.0 | 60.0 | — | 40.0 | — |
| EJOT 9652055105 | 80.0 | 12.0 | 70.0 | — | 5.0 | — |
| EJOT 9652055115 | 90.0 | 12.0 | 70.0 | 12.0 | 15.0 | 15.0 |
| EJOT 9652055140 | 115.0 | 12.0 | 70.0 | 12.0 | 40.0 | 40.0 |
| EJOT 9655070105 | 95.0 | 15.0 | 85.0 | — | 5.0 | — |
| EJOT 9655070115 | 105.0 | 15.0 | 85.0 | 15.0 | 15.0 | 15.0 |
| EJOT 9655070140 | 130.0 | 15.0 | 85.0 | 15.0 | 40.0 | 40.0 |
| EJOT 9650080105 | 113.0 | 20.0 | 100.0 | — | 5.0 | — |
| EJOT 9650080115 | 123.0 | 20.0 | 100.0 | 20.0 | 15.0 | 15.0 |
| EJOT 9650080140 | 148.0 | 20.0 | 100.0 | 20.0 | 40.0 | 40.0 |
| EJOT 9655100105 | 145.0 | 25.0 | 125.0 | — | 5.0 | — |
| EJOT 9655100115 | 155.0 | 25.0 | 125.0 | 25.0 | 15.0 | 15.0 |
| EJOT 9655100140 | 180.0 | 25.0 | 125.0 | 25.0 | 40.0 | 40.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Tassello di sicurezza LIEBIG® BEJOT · 23 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.Full description and technical table ↓

Series characteristics Tassello di sicurezza LIEBIG® B
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.
Materials represented by the variants: Steel.
Documented series dimensions: length 70–245 mm; thread Ø 10–25 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Length (mm) | Thread Ø (mm) | Hole depth ≤ (mm), source wording | Drill bit Ø (mm) | Fixture thickness B ≥ (mm) | Fixture thickness (mm) |
|---|---|---|---|---|---|---|
| EJOT 9650045005 | 70.0 | 10.0 | 60.0 | 10.0 | 5.0 | 5.0 |
| EJOT 9650045015 | 80.0 | 10.0 | 60.0 | 10.0 | 15.0 | 15.0 |
| EJOT 9650045040 | 105.0 | 10.0 | 60.0 | — | 40.0 | — |
| EJOT 9652055005 | 85.0 | 12.0 | 70.0 | — | 5.0 | — |
| EJOT 9652055015 | 95.0 | 12.0 | 70.0 | 12.0 | 15.0 | 15.0 |
| EJOT 9652055040 | 120.0 | 12.0 | 70.0 | 12.0 | 40.0 | 40.0 |
| EJOT 9652055065 | 145.0 | 12.0 | 75.0 | — | 65.0 | — |
| EJOT 9652055100 | 180.0 | 12.0 | 70.0 | — | 100.0 | — |
| EJOT 9655070005 | 100.0 | 15.0 | 85.0 | — | 5.0 | — |
| EJOT 9655070015 | 110.0 | 15.0 | 85.0 | 15.0 | 15.0 | 15.0 |
| EJOT 9655070040 | 135.0 | 15.0 | 85.0 | 15.0 | 40.0 | 40.0 |
| EJOT 9655070065 | 160.0 | 15.0 | 85.0 | — | 65.0 | — |
| EJOT 9655070100 | 195.0 | 15.0 | 85.0 | — | 100.0 | — |
| EJOT 9650080005 | 120.0 | 20.0 | 100.0 | — | 5.0 | — |
| EJOT 9650080040 | 155.0 | 20.0 | 100.0 | 20.0 | 40.0 | 40.0 |
| EJOT 9650080065 | 180.0 | 20.0 | 100.0 | — | 65.0 | — |
| EJOT 9650080100 | 215.0 | 20.0 | 100.0 | — | 100.0 | — |
| EJOT 9650280015 | 130.0 | 20.0 | 100.0 | 20.0 | 15.0 | 15.0 |
| EJOT 9655100005 | 150.0 | 25.0 | 125.0 | — | 5.0 | — |
| EJOT 9655100015 | 160.0 | 25.0 | 125.0 | 25.0 | 15.0 | 15.0 |
| EJOT 9655100040 | 185.0 | 25.0 | 125.0 | 25.0 | 40.0 | 40.0 |
| EJOT 9655100065 | 210.0 | 25.0 | 125.0 | — | 65.0 | — |
| EJOT 9655100100 | 245.0 | 25.0 | 125.0 | — | 100.0 | — |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
LIEBIG® SUPERPLUS ILSEJOT · 1 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.Full description and technical table ↓

Series characteristics LIEBIG® SUPERPLUS ILS
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.
Materials represented by the variants: Steel.
Documented series dimensions: length 95 mm; thread Ø 14 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Material | Length (mm) | Thread Ø (mm) | Hole depth ≤ (mm), source wording |
|---|---|---|---|---|
| EJOT 9650814080 | Acciaio al carbonio | 95.0 | 14.0 | 100.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
LIEBIG® SUPERPLUS BLS A4EJOT · 3 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: undercut anchorage.Full description and technical table ↓

Series characteristics LIEBIG® SUPERPLUS BLS A4
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: undercut anchorage.
Materials represented by the variants: Stainless A4.
Documented series dimensions: length 130–220 mm; thread Ø 14–25 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal size | Length (mm) | Thread Ø (mm) | Hole depth ≤ (mm), source wording | Fixture thickness B ≥ (mm) | Fixture thickness (mm) |
|---|---|---|---|---|---|---|
| EJOT 9654080254 | M8 | 130.0 | 14.0 | 100.0 | 25.0 | 25.0 |
| EJOT 9650080154 | M12 | 130.0 | 20.0 | 105.0 | 15.0 | 15.0 |
| EJOT 9655150304 | M16 | 220.0 | 25.0 | 185.0 | 30.0 | 30.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
LIEBIG® SUPERPLUS BLS M8-14 A4EJOT · 1 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.Full description and technical table ↓

Series characteristics LIEBIG® SUPERPLUS BLS M8-14 A4
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document.
Materials represented by the variants: Stainless A4.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source |
|---|
| EJOT 9650814085 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
LIEBIG® SUPERPLUS BLSEJOT · 7 referencesAnchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: undercut anchorage.Full description and technical table ↓

Series characteristics LIEBIG® SUPERPLUS BLS
Anchoring system for applications requiring specific assessment of load transfer. Expansion or undercut geometry and installation configuration must be identified in the product document. Series design: undercut anchorage.
Materials represented by the variants: Steel.
Documented series dimensions: length 130–300 mm; thread Ø 14–25 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.
Part identification, ETA and installation configuration are required. Check member thickness, edges, spacing, reinforcement, combined loads and manufacturer-specified setting equipment.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal size | Length (mm) | Thread Ø (mm) | Hole depth ≤ (mm), source wording | Drill bit Ø (mm) | Fixture thickness B ≥ (mm) | Fixture thickness (mm) |
|---|---|---|---|---|---|---|---|
| EJOT 9654080025 | M8 | 130.0 | 14.0 | 100.0 | 8.0 | 25.0 | 25.0 |
| EJOT 9650080015 | M12 | 130.0 | 20.0 | 105.0 | 12.0 | 15.0 | 15.0 |
| EJOT 9650080030 | M12 | 145.0 | 20.0 | 105.0 | 12.0 | 30.0 | 30.0 |
| EJOT 9655150030 | M16 | 220.0 | 25.0 | 185.0 | 16.0 | 30.0 | 30.0 |
| EJOT 9655150404 | M16 | 230.0 | 25.0 | 185.0 | — | 40.0 | 40.0 |
| EJOT 9655200040 | M16 | 280.0 | 25.0 | 235.0 | 16.0 | 40.0 | 40.0 |
| EJOT 9655200060 | M16 | 300.0 | 25.0 | 235.0 | 16.0 | 60.0 | 60.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Anchor finder
Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.
Request technical review or a quotation
Select a finder reference or describe the application.
FAQ
How do I select an anchor?
Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.
Does equal diameter mean equal capacity?
No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.
Do all anchors have an ETA and CE marking?
These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.
What information is needed for an enquiry?
Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.
Sources and documentation
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.