Hammer-in fixings
A hammer-driven nail or screw expands the body during installation. Collar, countersunk and cylindrical-head versions suit different fixture geometries.

Features and selection criteria
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Designs, materials and substrates
This family contains 17 series or reference groups, with 132 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.
Documented materials
Steel · Nylon · Stainless A2 · Zinc alloy
Substrates mentioned in the sources
Concrete
This list describes the family and does not assign every substrate to every variant.
Information to define before selection
| Parameter | What to check |
|---|---|
| Load-bearing substrate | Material type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size. |
| Fixing geometry | Total length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers. |
| Depth and distances | Compare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity. |
| Environment and exposure | Check material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment. |
| Loads and documentation | Define action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification. |
Installation sequence to verify
- Check body diameter and the fixture clearance hole.
- Drill to the specified depth beyond the fixture assembly.
- Insert the plug until the collar or head bears on the fixture.
- Activate the nail or screw as instructed, avoiding excessive hammering.
This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.
Series and technical tables
EB01Tecfi · 13 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination. Series design: flanged bearing, flange nut.Full description and technical table ↓

Series characteristics EB01
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination. Series design: flanged bearing, flange nut.
Materials represented by the variants: Steel.
Documented series dimensions: nominal Ø 6–16 mm; length 45–120 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Nominal Ø dnom (mm) | Length L (mm) | Material | Finish | Fixture thickness (mm) tfix |
|---|---|---|---|---|---|
| Tecfi EB 01 06 045 | 6 | 45 | Steel | Zinc plated | 5 |
| Tecfi EB 01 06 060 | 6 | 60 | Steel | Zinc plated | 20 |
| Tecfi EB 01 08 050 | 8 | 50 | Steel | Zinc plated | 5 |
| Tecfi EB 01 08 070 | 8 | 70 | Steel | Zinc plated | 25 |
| Tecfi EB 01 10 060 | 10 | 60 | Steel | Zinc plated | 5 |
| Tecfi EB 01 10 080 | 10 | 80 | Steel | Zinc plated | 25 |
| Tecfi EB 01 10 100 | 10 | 100 | Steel | Zinc plated | 45 |
| Tecfi EB 01 10 120 | 10 | 120 | Steel | Zinc plated | 65 |
| Tecfi EB 01 12 070 | 12 | 70 | Steel | Zinc plated | 5 |
| Tecfi EB 01 12 090 | 12 | 90 | Steel | Zinc plated | 25 |
| Tecfi EB 01 12 120 | 12 | 120 | Steel | Zinc plated | 55 |
| Tecfi EB 01 16 100 | 16 | 100 | Steel | Zinc plated | 5 |
| Tecfi EB 01 16 120 | 16 | 120 | Steel | Zinc plated | 25 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ01Tecfi · 16 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ01
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 5–8 mm; length 30–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi YZ 01 05 030 | 5 | 30 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 35 |
| Tecfi YZ 01 05 040 | 5 | 40 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 45 |
| Tecfi YZ 01 05 050 | 5 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 55 |
| Tecfi YZ 01 06 035 | 6 | 35 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 40 |
| Tecfi YZ 01 06 040 | 6 | 40 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 45 |
| Tecfi YZ 01 06 050 | 6 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 55 |
| Tecfi YZ 01 06 060 | 6 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 65 |
| Tecfi YZ 01 06 080 | 6 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 85 |
| Tecfi YZ 01 06 100 | 6 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 105 |
| Tecfi YZ 01 08 045 | 8 | 45 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 50 |
| Tecfi YZ 01 08 060 | 8 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 65 |
| Tecfi YZ 01 08 080 | 8 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 85 |
| Tecfi YZ 01 08 100 | 8 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 105 |
| Tecfi YZ 01 08 120 | 8 | 120 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 125 |
| Tecfi YZ 01 08 135 | 8 | 135 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 140 |
| Tecfi YZ 01 08 160 | 8 | 160 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 165 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE01Tecfi · 5 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics BE01
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 10 mm; length 80–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish |
|---|---|---|---|---|---|
| Tecfi BE 01 10 080 | 10 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated |
| Tecfi BE 01 10 100 | 10 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated |
| Tecfi BE 01 10 120 | 10 | 120 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated |
| Tecfi BE 01 10 135 | 10 | 135 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated |
| Tecfi BE 01 10 160 | 10 | 160 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ31Tecfi · 16 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ31
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 5–8 mm; length 30–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi YZ 31 05 030 | 5 | 30 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 35 |
| Tecfi YZ 31 05 040 | 5 | 40 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 45 |
| Tecfi YZ 31 05 050 | 5 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 55 |
| Tecfi YZ 31 06 035 | 6 | 35 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 40 |
| Tecfi YZ 31 06 040 | 6 | 40 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 45 |
| Tecfi YZ 31 06 050 | 6 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 55 |
| Tecfi YZ 31 06 060 | 6 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 65 |
| Tecfi YZ 31 06 080 | 6 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 85 |
| Tecfi YZ 31 06 100 | 6 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 105 |
| Tecfi YZ 31 08 045 | 8 | 45 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 50 |
| Tecfi YZ 31 08 060 | 8 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 65 |
| Tecfi YZ 31 08 080 | 8 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 85 |
| Tecfi YZ 31 08 100 | 8 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 105 |
| Tecfi YZ 31 08 120 | 8 | 120 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 125 |
| Tecfi YZ 31 08 135 | 8 | 135 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 140 |
| Tecfi YZ 31 08 160 | 8 | 160 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 4.6 | 165 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE06Tecfi · 3 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics BE06
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 5 mm; length 25–45 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 06 05 025 | 5 | 25 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 30 |
| Tecfi BE 06 05 035 | 5 | 35 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 40 |
| Tecfi BE 06 05 045 | 5 | 45 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio | Zinc plated | 3.4 | 50 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ51Tecfi · 12 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ51
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Stainless A2, Nylon.
Documented series dimensions: nominal Ø 5–8 mm; length 30–135 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi YZ 51 05 030 | 5 | 30 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.4 | 35 |
| Tecfi YZ 51 05 050 | 5 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.4 | 55 |
| Tecfi YZ 51 06 040 | 6 | 40 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 45 |
| Tecfi YZ 51 06 050 | 6 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 55 |
| Tecfi YZ 51 06 060 | 6 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 65 |
| Tecfi YZ 51 06 080 | 6 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 85 |
| Tecfi YZ 51 06 100 | 6 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 105 |
| Tecfi YZ 51 08 060 | 8 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 65 |
| Tecfi YZ 51 08 080 | 8 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 85 |
| Tecfi YZ 51 08 100 | 8 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 105 |
| Tecfi YZ 51 08 120 | 8 | 120 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 125 |
| Tecfi YZ 51 08 135 | 8 | 135 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 140 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ52Tecfi · 12 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ52
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Stainless A2, Nylon.
Documented series dimensions: nominal Ø 5–8 mm; length 30–135 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi YZ 52 05 030 | 5 | 30 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.4 | 35 |
| Tecfi YZ 52 05 050 | 5 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.4 | 55 |
| Tecfi YZ 52 06 040 | 6 | 40 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 45 |
| Tecfi YZ 52 06 050 | 6 | 50 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 55 |
| Tecfi YZ 52 06 060 | 6 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 65 |
| Tecfi YZ 52 06 080 | 6 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 85 |
| Tecfi YZ 52 06 100 | 6 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 3.8 | 105 |
| Tecfi YZ 52 08 060 | 8 | 60 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 65 |
| Tecfi YZ 52 08 080 | 8 | 80 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 85 |
| Tecfi YZ 52 08 100 | 8 | 100 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 105 |
| Tecfi YZ 52 08 120 | 8 | 120 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 125 |
| Tecfi YZ 52 08 135 | 8 | 135 | Impronta a Croce tipo Z / A percussione | Nylon / Acciaio Inox A2 | 4.6 | 140 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE12Tecfi · 3 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics BE12
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 6–8 mm; length 45–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Misura vite M |
|---|---|---|---|---|---|---|---|---|
| Tecfi BE 12 06 060 | 6 | 60 | Impronta a Taglio / A percussione | Nylon / Acciaio | Zinc plated | 3.8 | 65 | M6 |
| Tecfi BE 12 08 045 | 8 | 45 | Impronta a Taglio / A percussione | Nylon / Acciaio | Zinc plated | 4.8 | 50 | M8 |
| Tecfi BE 12 08 060 | 8 | 60 | Impronta a Taglio / A percussione | Nylon / Acciaio | Zinc plated | 4.8 | 65 | M8 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
DM01Tecfi · 6 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination. Series design: nail activation.Full description and technical table ↓

Series characteristics DM01
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination. Series design: nail activation.
Materials represented by the variants: Steel, Zinc alloy.
Documented series dimensions: nominal Ø 5–6 mm; length 20–65 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Material | Finish |
|---|---|---|---|---|
| Tecfi DM 01 05 022 | 5 | 22 | Lega di zinco / Acciaio | Zinc plated |
| Tecfi DM 01 06 020 | 6 | 20 | Lega di zinco / Acciaio | Zinc plated |
| Tecfi DM 01 06 030 | 6 | 30 | Lega di zinco / Acciaio | Zinc plated |
| Tecfi DM 01 06 040 | 6 | 40 | Lega di zinco / Acciaio | Zinc plated |
| Tecfi DM 01 06 050 | 6 | 50 | Lega di zinco / Acciaio | Zinc plated |
| Tecfi DM 01 06 065 | 6 | 65 | Lega di zinco / Acciaio | Zinc plated |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ61Tecfi · 7 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ61
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 5–6 mm; length 30–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor length (mm) | Anchor body Ø (mm) | Material | Finish | Drive | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi YZ 61 05 030 | 30 | 5 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.4 | 35 |
| Tecfi YZ 61 06 035 | 35 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 40 |
| Tecfi YZ 61 06 040 | 40 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 45 |
| Tecfi YZ 61 06 050 | 50 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 55 |
| Tecfi YZ 61 06 060 | 60 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 65 |
| Tecfi YZ 61 06 080 | 80 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 85 |
| Tecfi YZ 61 06 100 | 100 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 105 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZB61Tecfi · 1 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZB61
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 6 mm; length 35 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor length (mm) | Anchor body Ø (mm) | Material | Finish |
|---|---|---|---|---|
| Tecfi YZB 61 06 035 | 35 | 6 | Nylon / Acciaio | Zinc plated |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ54Tecfi · 6 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ54
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Stainless A2, Nylon.
Documented series dimensions: nominal Ø 5–6 mm; length 30–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor length (mm) | Anchor body Ø (mm) | Material | Drive | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|
| Tecfi YZ 54 05 030 | 30 | 5 | Nylon / Acciaio Inox A2 | Impronta a Croce tipo Z / A percussione | 3.4 | 35 |
| Tecfi YZ 54 06 040 | 40 | 6 | Nylon / Acciaio Inox A2 | Impronta a Croce tipo Z / A percussione | 3.8 | 45 |
| Tecfi YZ 54 06 050 | 50 | 6 | Nylon / Acciaio Inox A2 | Impronta a Croce tipo Z / A percussione | 3.8 | 55 |
| Tecfi YZ 54 06 060 | 60 | 6 | Nylon / Acciaio Inox A2 | Impronta a Croce tipo Z / A percussione | 3.8 | 65 |
| Tecfi YZ 54 06 080 | 80 | 6 | Nylon / Acciaio Inox A2 | Impronta a Croce tipo Z / A percussione | 3.8 | 85 |
| Tecfi YZ 54 06 100 | 100 | 6 | Nylon / Acciaio Inox A2 | Impronta a Croce tipo Z / A percussione | 3.8 | 105 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ60Tecfi · 8 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ60
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 5–6 mm; length 30–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor length (mm) | Anchor body Ø (mm) | Material | Finish | Drive | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi YZ 60 05 030 | 30 | 5 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.4 | 35 |
| Tecfi BD 01 06 030 | 30 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 4 | 30 |
| Tecfi YZ 60 06 035 | 35 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 40 |
| Tecfi YZ 60 06 040 | 40 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 45 |
| Tecfi YZ 60 06 050 | 50 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 55 |
| Tecfi YZ 60 06 060 | 60 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 65 |
| Tecfi YZ 60 06 080 | 80 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 85 |
| Tecfi YZ 60 06 100 | 100 | 6 | Nylon / Acciaio | Zinc plated | Impronta a Croce tipo Z / A percussione | 3.8 | 105 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ62Tecfi · 8 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ62
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 5–6 mm; length 30–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor length (mm) | Anchor body Ø (mm) | Material | Finish | Drive | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi YZ 62 05 030 | 30 | 5 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 3.4 | 35 |
| Tecfi BD 02 06 030 | 30 | 6 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 4 | 30 |
| Tecfi YZ 62 06 035 | 35 | 6 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 3.8 | 40 |
| Tecfi YZ 62 06 040 | 40 | 6 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 3.8 | 45 |
| Tecfi YZ 62 06 050 | 50 | 6 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 3.8 | 55 |
| Tecfi YZ 62 06 060 | 60 | 6 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 3.8 | 65 |
| Tecfi YZ 62 06 080 | 80 | 6 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 3.8 | 85 |
| Tecfi YZ 62 06 100 | 100 | 6 | Nylon / Acciaio | Zincato nero | Impronta a Croce tipo Z / A percussione | 3.8 | 105 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
YZ65Tecfi · 4 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics YZ65
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Stainless A2, Nylon.
Documented series dimensions: nominal Ø 6 mm; length 30–60 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor length (mm) | Anchor body Ø (mm) | Material | Finish | Drive | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BD 05 06 030 | 30 | 6 | Nylon / Acciaio Inox A2 | Ramato | Impronta a Croce tipo Z / A percussione | 4 | 30 |
| Tecfi YZ 65 06 040 | 40 | 6 | Nylon / Acciaio Inox A2 | Ramato | Impronta a Croce tipo Z / A percussione | 4 | 40 |
| Tecfi YZ 65 06 050 | 50 | 6 | Nylon / Acciaio Inox A2 | Ramato | Impronta a Croce tipo Z / A percussione | 4 | 50 |
| Tecfi YZ 65 06 060 | 60 | 6 | Nylon / Acciaio Inox A2 | Ramato | Impronta a Croce tipo Z / A percussione | 4 | 60 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
ND-K-6EJOT · 2 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination. Series design: nail activation.Full description and technical table ↓

Series characteristics ND-K-6
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination. Series design: nail activation.
Documented series dimensions: length 45–55 mm; thread Ø 6 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8561645400 | 6.0 | Zinc plated | 45.0 | 15.0 |
| EJOT 8561655400 | 6.0 | Zinc plated | 55.0 | 25.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Tassello a percussione ND-SEJOT · 10 referencesHammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.Full description and technical table ↓

Series characteristics Tassello a percussione ND-S
Hammer-activated fixing. The body and expansion element must be considered in the manufacturer-specified combination.
Materials represented by the variants: Steel.
Documented series dimensions: length 30–160 mm; thread Ø 5–8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Check fixture thickness, drill diameter and depth, and declared substrates. A removable pin does not establish plug reusability or permit reinstallation in the same hole.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Anchor length (mm) |
|---|---|---|---|
| EJOT 9650075658 | 5.0 | Acciaio al carbonio | 30.0 |
| EJOT 9650075660 | 6.0 | Acciaio al carbonio | 40.0 |
| EJOT 9650075659 | 5.0 | Acciaio al carbonio | 50.0 |
| EJOT 9650075661 | 6.0 | Acciaio al carbonio | 60.0 |
| EJOT 9650075665 | 8.0 | Acciaio al carbonio | 60.0 |
| EJOT 9650075662 | 6.0 | Acciaio al carbonio | 80.0 |
| EJOT 9650075664 | 8.0 | Acciaio al carbonio | 100.0 |
| EJOT 9650075610 | 8.0 | Acciaio al carbonio | 120.0 |
| EJOT 9650075611 | 8.0 | Acciaio al carbonio | 120.0 |
| EJOT 9650075612 | 8.0 | Acciaio al carbonio | 160.0 |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Anchor finder
Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.
Request technical review or a quotation
Select a finder reference or describe the application.
FAQ
How do I select an anchor?
Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.
Does equal diameter mean equal capacity?
No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.
Do all anchors have an ETA and CE marking?
These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.
What information is needed for an enquiry?
Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.
Sources and documentation
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.