Frame and facade fixings
Frame fixings allow installation through the fixture. The expansion zone must reach the load-bearing substrate beyond the bracket, plaster and non-load-bearing layers.

Features and selection criteria
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Designs, materials and substrates
This family contains 51 series or reference groups, with 535 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.
Documented materials
Nylon · Steel · Stainless A4 · Stainless A2
Substrates mentioned in the sources
Concrete · Cracked concrete · Masonry · Perforated masonry · Aerated concrete · Insulation
This list describes the family and does not assign every substrate to every variant.
Information to define before selection
| Parameter | What to check |
|---|---|
| Load-bearing substrate | Material type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size. |
| Fixing geometry | Total length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers. |
| Depth and distances | Compare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity. |
| Environment and exposure | Check material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment. |
| Loads and documentation | Define action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification. |
Installation sequence to verify
- Measure the traversed assembly: fixture, stand-offs, plaster and non-load-bearing layers.
- Select a length ensuring anchorage in the load-bearing substrate.
- Drill and clean using the method specified for the substrate and design.
- Install the specified plug-and-screw combination and check bracket bearing.
This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.
Series and technical tables
VS11Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS11
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VS 11 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VS 11 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VS 11 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VS 11 08 140 | 8 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VS 11 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VS 11 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VS 11 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VS 11 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VS 11 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VS 11 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
| Tecfi VS 11 10 230 | 10 | 230 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 235 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS13Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS13
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Stainless A4, Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi VS 13 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 85 | ETA-CE |
| Tecfi VS 13 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 105 | ETA-CE |
| Tecfi VS 13 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 125 | ETA-CE |
| Tecfi VS 13 08 140 | 8 | 140 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 145 | ETA-CE |
| Tecfi VS 13 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 85 | ETA-CE R90 |
| Tecfi VS 13 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 105 | ETA-CE R90 |
| Tecfi VS 13 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 125 | ETA-CE R90 |
| Tecfi VS 13 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 145 | ETA-CE R90 |
| Tecfi VS 13 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 165 | ETA-CE R90 |
| Tecfi VS 13 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 205 | ETA-CE R90 |
| Tecfi VS 13 10 230 | 10 | 230 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 235 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS12Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS12
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi VS 12 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 85 |
| Tecfi VS 12 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 105 |
| Tecfi VS 12 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 125 |
| Tecfi VS 12 08 140 | 8 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 145 |
| Tecfi VS 12 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 85 |
| Tecfi VS 12 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 105 |
| Tecfi VS 12 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 125 |
| Tecfi VS 12 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 145 |
| Tecfi VS 12 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 165 |
| Tecfi VS 12 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 205 |
| Tecfi VS 12 10 230 | 10 | 230 | Impronta a 6 lobi | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 235 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS31Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS31
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VS 31 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VS 31 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VS 31 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VS 31 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VS 31 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VS 31 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VS 31 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VS 31 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VS 31 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VS 31 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
| Tecfi VS 31 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 235 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS33Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS33
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Stainless A4, Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi VS 33 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 85 | ETA-CE |
| Tecfi VS 33 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 105 | ETA-CE |
| Tecfi VS 33 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 125 | ETA-CE |
| Tecfi VS 33 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 145 | ETA-CE |
| Tecfi VS 33 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 85 | ETA-CE R90 |
| Tecfi VS 33 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 105 | ETA-CE R90 |
| Tecfi VS 33 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 125 | ETA-CE R90 |
| Tecfi VS 33 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 145 | ETA-CE R90 |
| Tecfi VS 33 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 165 | ETA-CE R90 |
| Tecfi VS 33 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 205 | ETA-CE R90 |
| Tecfi VS 33 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 235 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS32Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS32
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi VS 32 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 85 |
| Tecfi VS 32 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 105 |
| Tecfi VS 32 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 125 |
| Tecfi VS 32 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 145 |
| Tecfi VS 32 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 85 |
| Tecfi VS 32 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 105 |
| Tecfi VS 32 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 125 |
| Tecfi VS 32 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 145 |
| Tecfi VS 32 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 165 |
| Tecfi VS 32 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 205 |
| Tecfi VS 32 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 235 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS21Tecfi · 10 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS21
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VS 21 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VS 21 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VS 21 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VS 21 08 140 | 8 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VS 21 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VS 21 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VS 21 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VS 21 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VS 21 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VS 21 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS71Tecfi · 10 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS71
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VS 71 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VS 71 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VS 71 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VS 71 08 140 | 8 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VS 71 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VS 71 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VS 71 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VS 71 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VS 71 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VS 71 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS81Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS81
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VS 81 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VS 81 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VS 81 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VS 81 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VS 81 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VS 81 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VS 81 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VS 81 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VS 81 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VS 81 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
| Tecfi VS 81 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 235 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS83Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS83
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Stainless A4, Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi VS 83 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 85 | ETA-CE |
| Tecfi VS 83 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 105 | ETA-CE |
| Tecfi VS 83 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 125 | ETA-CE |
| Tecfi VS 83 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 145 | ETA-CE |
| Tecfi VS 83 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 85 | ETA-CE R90 |
| Tecfi VS 83 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 105 | ETA-CE R90 |
| Tecfi VS 83 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 125 | ETA-CE R90 |
| Tecfi VS 83 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 145 | ETA-CE R90 |
| Tecfi VS 83 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 165 | ETA-CE R90 |
| Tecfi VS 83 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 205 | ETA-CE R90 |
| Tecfi VS 83 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 235 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS82Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS82
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi VS 82 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 85 |
| Tecfi VS 82 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 105 |
| Tecfi VS 82 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 125 |
| Tecfi VS 82 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 6 | 145 |
| Tecfi VS 82 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 85 |
| Tecfi VS 82 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 105 |
| Tecfi VS 82 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 125 |
| Tecfi VS 82 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 145 |
| Tecfi VS 82 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 165 |
| Tecfi VS 82 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 205 |
| Tecfi VS 82 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Steel Saver - 1000h - ZL | 7 | 235 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS41Tecfi · 4 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS41
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Fixture thickness (mm) tfix | Vite doppio Filetto Øs (mm) | Vite doppio filetto Ls (mm) | Vite doppio Filetto M | Vite doppio filetto LM (mm) | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Tecfi VS 41 08 080 | 8 | 80 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 10 | 6 | 85 | M6 | 21 | ETA-CE |
| Tecfi VS 41 10 080 | 10 | 80 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 10 | 7 | 85 | M8 | 25 | ETA-CE R90 |
| Tecfi VS 41 10 160 | 10 | 160 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 90 | 7 | 165 | M8 | 20 | ETA-CE R90 |
| Tecfi VS 41 10 200 | 10 | 200 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 130 | 7 | 205 | M8 | 20 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS43Tecfi · 2 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS43
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Stainless A4, Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Fixture thickness (mm) tfix | Vite doppio Filetto Øs (mm) | Vite doppio filetto Ls (mm) | Vite doppio Filetto M | Vite doppio filetto LM (mm) | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|---|---|
| Tecfi VS 43 08 080 | 8 | 80 | Chiave / Cava Esagonale | Nylon / Acciaio Inox A4 | 10 | 6 | 85 | M6 | 21 | ETA-CE |
| Tecfi VS 43 10 080 | 10 | 80 | Chiave / Cava Esagonale | Nylon / Acciaio Inox A4 | 10 | 7 | 85 | M8 | 25 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS91Tecfi · 4 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VS91
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Fixture thickness (mm) tfix | Vite doppio Filetto Øs (mm) | Vite doppio filetto Ls (mm) | Vite doppio Filetto M | Vite doppio filetto LM (mm) | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Tecfi VS 91 08 080 | 8 | 80 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 10 | 6 | 85 | M6 | 21 | ETA-CE |
| Tecfi VS 91 10 080 | 10 | 80 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 10 | 7 | 85 | M8 | 25 | ETA-CE R90 |
| Tecfi VS 91 10 160 | 10 | 160 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 90 | 7 | 165 | M8 | 20 | ETA-CE R90 |
| Tecfi VS 91 10 200 | 10 | 200 | Chiave / Cava Esagonale | Nylon / Acciaio | Zinc plated | 130 | 7 | 205 | M8 | 20 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VS61Tecfi · 4 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: stop collar.Full description and technical table ↓

Series characteristics VS61
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: stop collar.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 10 mm; length 140–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Fixture thickness (mm) tfix | Vite doppio Filetto Øs (mm) | Vite doppio filetto Ls (mm) | Vite doppio Filetto M | Vite doppio filetto LM (mm) | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Tecfi VS 61 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 70 | 7 | 145 | M8 | 9 | ETA-CE R90 |
| Tecfi VS 61 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 90 | 7 | 165 | M8 | 9 | ETA-CE R90 |
| Tecfi VS 61 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 130 | 7 | 205 | M8 | 9 | ETA-CE R90 |
| Tecfi VS 61 10 230 | 10 | 230 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 160 | 7 | 235 | M8 | 9 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX11Tecfi · 19 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: countersunk head.Full description and technical table ↓

Series characteristics VSX11
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: countersunk head.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VSX 11 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VSX 11 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VSX 11 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VSX 11 08 140 | 8 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VSX 11 08 160 | 8 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 165 | ETA-CE |
| Tecfi VSX 11 08 180 | 8 | 180 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 185 | ETA-CE |
| Tecfi VSX 11 08 200 | 8 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 205 | ETA-CE |
| Tecfi VSX 11 08 230 | 8 | 230 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 6 | 235 | ETA-CE |
| Tecfi VSX 11 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VSX 11 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VSX 11 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VSX 11 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VSX 11 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VSX 11 10 180 | 10 | 180 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 185 | ETA-CE R90 |
| Tecfi VSX 11 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
| Tecfi VSX 11 10 230 | 10 | 230 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 235 | ETA-CE R90 |
| Tecfi VSX 11 10 260 | 10 | 260 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 265 | ETA-CE R90 |
| Tecfi VSX 11 10 280 | 10 | 280 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 285 | ETA-CE R90 |
| Tecfi VSX 11 10 300 | 10 | 300 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 305 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX13Tecfi · 19 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: countersunk head.Full description and technical table ↓

Series characteristics VSX13
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: countersunk head.
Materials represented by the variants: Stainless A4, Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi VSX 13 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 85 | ETA-CE |
| Tecfi VSX 13 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 105 | ETA-CE |
| Tecfi VSX 13 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 125 | ETA-CE |
| Tecfi VSX 13 08 140 | 8 | 140 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 145 | ETA-CE |
| Tecfi VSX 13 08 160 | 8 | 160 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 165 | ETA-CE |
| Tecfi VSX 13 08 180 | 8 | 180 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 185 | ETA-CE |
| Tecfi VSX 13 08 200 | 8 | 200 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 205 | ETA-CE |
| Tecfi VSX 13 08 230 | 8 | 230 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 6 | 235 | ETA-CE |
| Tecfi VSX 13 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 85 | ETA-CE R90 |
| Tecfi VSX 13 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 105 | ETA-CE R90 |
| Tecfi VSX 13 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 125 | ETA-CE R90 |
| Tecfi VSX 13 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 145 | ETA-CE R90 |
| Tecfi VSX 13 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 165 | ETA-CE R90 |
| Tecfi VSX 13 10 180 | 10 | 180 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 185 | ETA-CE R90 |
| Tecfi VSX 13 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 205 | ETA-CE R90 |
| Tecfi VSX 13 10 230 | 10 | 230 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 235 | ETA-CE R90 |
| Tecfi VSX 13 10 260 | 10 | 260 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 265 | ETA-CE R90 |
| Tecfi VSX 13 10 280 | 10 | 280 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 285 | ETA-CE R90 |
| Tecfi VSX 13 10 300 | 10 | 300 | Impronta a 6 lobi | Nylon / Acciaio Inox A4 | 7 | 305 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX31Tecfi · 19 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.Full description and technical table ↓

Series characteristics VSX31
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VSX 31 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VSX 31 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VSX 31 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VSX 31 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VSX 31 08 160 | 8 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 165 | ETA-CE |
| Tecfi VSX 31 08 180 | 8 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 185 | ETA-CE |
| Tecfi VSX 31 08 200 | 8 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 205 | ETA-CE |
| Tecfi VSX 31 08 230 | 8 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 235 | ETA-CE |
| Tecfi VSX 31 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VSX 31 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VSX 31 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VSX 31 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VSX 31 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VSX 31 10 180 | 10 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 185 | ETA-CE R90 |
| Tecfi VSX 31 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
| Tecfi VSX 31 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 235 | ETA-CE R90 |
| Tecfi VSX 31 10 260 | 10 | 260 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 265 | ETA-CE R90 |
| Tecfi VSX 31 10 280 | 10 | 280 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 285 | ETA-CE R90 |
| Tecfi VSX 31 10 300 | 10 | 300 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 305 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX33Tecfi · 19 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.Full description and technical table ↓

Series characteristics VSX33
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.
Materials represented by the variants: Stainless A4, Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi VSX 33 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 85 | ETA-CE |
| Tecfi VSX 33 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 105 | ETA-CE |
| Tecfi VSX 33 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 125 | ETA-CE |
| Tecfi VSX 33 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 145 | ETA-CE |
| Tecfi VSX 33 08 160 | 8 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 165 | ETA-CE |
| Tecfi VSX 33 08 180 | 8 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 185 | ETA-CE |
| Tecfi VSX 33 08 200 | 8 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 205 | ETA-CE |
| Tecfi VSX 33 08 230 | 8 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 235 | ETA-CE |
| Tecfi VSX 33 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 85 | ETA-CE R90 |
| Tecfi VSX 33 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 105 | ETA-CE R90 |
| Tecfi VSX 33 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 125 | ETA-CE R90 |
| Tecfi VSX 33 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 145 | ETA-CE R90 |
| Tecfi VSX 33 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 165 | ETA-CE R90 |
| Tecfi VSX 33 10 180 | 10 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 185 | ETA-CE R90 |
| Tecfi VSX 33 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 205 | ETA-CE R90 |
| Tecfi VSX 33 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 235 | ETA-CE R90 |
| Tecfi VSX 33 10 260 | 10 | 260 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 265 | ETA-CE R90 |
| Tecfi VSX 33 10 280 | 10 | 280 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 285 | ETA-CE R90 |
| Tecfi VSX 33 10 300 | 10 | 300 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 305 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX26Tecfi · 5 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VSX26
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 10 mm; length 80–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VSX 26 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VSX 26 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VSX 26 10 120 | 10 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VSX 26 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VSX 26 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX81Tecfi · 19 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.Full description and technical table ↓

Series characteristics VSX81
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|
| Tecfi VSX 81 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 85 | ETA-CE |
| Tecfi VSX 81 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 105 | ETA-CE |
| Tecfi VSX 81 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 125 | ETA-CE |
| Tecfi VSX 81 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 145 | ETA-CE |
| Tecfi VSX 81 08 160 | 8 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 165 | ETA-CE |
| Tecfi VSX 81 08 180 | 8 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 185 | ETA-CE |
| Tecfi VSX 81 08 200 | 8 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 205 | ETA-CE |
| Tecfi VSX 81 08 230 | 8 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 6 | 235 | ETA-CE |
| Tecfi VSX 81 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 85 | ETA-CE R90 |
| Tecfi VSX 81 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 105 | ETA-CE R90 |
| Tecfi VSX 81 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 125 | ETA-CE R90 |
| Tecfi VSX 81 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 145 | ETA-CE R90 |
| Tecfi VSX 81 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 165 | ETA-CE R90 |
| Tecfi VSX 81 10 180 | 10 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 185 | ETA-CE R90 |
| Tecfi VSX 81 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 205 | ETA-CE R90 |
| Tecfi VSX 81 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 235 | ETA-CE R90 |
| Tecfi VSX 81 10 260 | 10 | 260 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 265 | ETA-CE R90 |
| Tecfi VSX 81 10 280 | 10 | 280 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 285 | ETA-CE R90 |
| Tecfi VSX 81 10 300 | 10 | 300 | Impronta a 6 lobi / Chiave | Nylon / Acciaio | Zinc plated | 7 | 305 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX83Tecfi · 19 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.Full description and technical table ↓

Series characteristics VSX83
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, flanged bearing.
Materials represented by the variants: Stainless A4, Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Diameter vite Øs | Length vite Ls | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|
| Tecfi VSX 83 08 080 | 8 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 85 | ETA-CE |
| Tecfi VSX 83 08 100 | 8 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 105 | ETA-CE |
| Tecfi VSX 83 08 120 | 8 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 125 | ETA-CE |
| Tecfi VSX 83 08 140 | 8 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 145 | ETA-CE |
| Tecfi VSX 83 08 160 | 8 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 165 | ETA-CE |
| Tecfi VSX 83 08 180 | 8 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 185 | ETA-CE |
| Tecfi VSX 83 08 200 | 8 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 205 | ETA-CE |
| Tecfi VSX 83 08 230 | 8 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 6 | 235 | ETA-CE |
| Tecfi VSX 83 10 080 | 10 | 80 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 85 | ETA-CE R90 |
| Tecfi VSX 83 10 100 | 10 | 100 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 105 | ETA-CE R90 |
| Tecfi VSX 83 10 120 | 10 | 120 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 125 | ETA-CE R90 |
| Tecfi VSX 83 10 140 | 10 | 140 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 145 | ETA-CE R90 |
| Tecfi VSX 83 10 160 | 10 | 160 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 165 | ETA-CE R90 |
| Tecfi VSX 83 10 180 | 10 | 180 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 185 | ETA-CE R90 |
| Tecfi VSX 83 10 200 | 10 | 200 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 205 | ETA-CE R90 |
| Tecfi VSX 83 10 230 | 10 | 230 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 235 | ETA-CE R90 |
| Tecfi VSX 83 10 260 | 10 | 260 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 265 | ETA-CE R90 |
| Tecfi VSX 83 10 280 | 10 | 280 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 285 | ETA-CE R90 |
| Tecfi VSX 83 10 300 | 10 | 300 | Impronta a 6 lobi / Chiave | Nylon / Acciaio Inox A4 | 7 | 305 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSX61Tecfi · 5 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: stop collar.Full description and technical table ↓

Series characteristics VSX61
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: stop collar.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 10 mm; length 140–230 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Vite doppio filetto Ls (mm) | Vite doppio Filetto M | Vite doppio filetto LM (mm) | Pz Confezione | Part-specific documentation indicators |
|---|---|---|---|---|---|---|---|---|---|---|
| Tecfi VSX 61 10 140 | 10 | 140 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 145 | M8 | 9 | ETA-CE R90 |
| Tecfi VSX 61 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 | M8 | 9 | ETA-CE R90 |
| Tecfi VSX 61 10 180 | 10 | 180 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 185 | M8 | 9 | ETA-CE R90 |
| Tecfi VSX 61 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 205 | M8 | 9 | ETA-CE R90 |
| Tecfi VSX 61 10 230 | 10 | 230 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 235 | M8 | 9 | ETA-CE R90 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
AT01Tecfi · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics AT01
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 75–165 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi AT 01 08 075 | 8 | 75 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5 | 85 |
| Tecfi AT 01 08 100 | 8 | 100 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5 | 110 |
| Tecfi AT 01 08 120 | 8 | 120 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5 | 130 |
| Tecfi AT 01 08 140 | 8 | 140 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5 | 150 |
| Tecfi AT 01 10 075 | 10 | 75 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 6 | 85 |
| Tecfi AT 01 10 100 | 10 | 100 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 6 | 110 |
| Tecfi AT 01 10 120 | 10 | 120 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 6 | 130 |
| Tecfi AT 01 10 140 | 10 | 140 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 6 | 150 |
| Tecfi AT 01 10 165 | 10 | 165 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 6 | 175 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
CN01Tecfi · 14 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics CN01
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon.
Documented series dimensions: nominal Ø 6–10 mm; length 40–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Material |
|---|---|---|---|
| Tecfi CN 01 06 040 | 6 | 40 | Nylon |
| Tecfi CN 01 06 060 | 6 | 60 | Nylon |
| Tecfi CN 01 06 080 | 6 | 80 | Nylon |
| Tecfi CN 01 08 060 | 8 | 60 | Nylon |
| Tecfi CN 01 08 080 | 8 | 80 | Nylon |
| Tecfi CN 01 08 100 | 8 | 100 | Nylon |
| Tecfi CN 01 08 120 | 8 | 120 | Nylon |
| Tecfi CN 01 08 135 | 8 | 135 | Nylon |
| Tecfi CN 01 10 060 | 10 | 60 | Nylon |
| Tecfi CN 01 10 080 | 10 | 80 | Nylon |
| Tecfi CN 01 10 100 | 10 | 100 | Nylon |
| Tecfi CN 01 10 115 | 10 | 115 | Nylon |
| Tecfi CN 01 10 135 | 10 | 135 | Nylon |
| Tecfi CN 01 10 160 | 10 | 160 | Nylon |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
CN02Tecfi · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics CN02
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Material |
|---|---|---|---|
| Tecfi CN 02 08 080 | 8 | 80 | Nylon |
| Tecfi CN 02 08 100 | 8 | 100 | Nylon |
| Tecfi CN 02 08 120 | 8 | 120 | Nylon |
| Tecfi CN 02 10 080 | 10 | 80 | Nylon |
| Tecfi CN 02 10 100 | 10 | 100 | Nylon |
| Tecfi CN 02 10 115 | 10 | 115 | Nylon |
| Tecfi CN 02 10 135 | 10 | 135 | Nylon |
| Tecfi CN 02 10 160 | 10 | 160 | Nylon |
| Tecfi CN 02 10 200 | 10 | 200 | Nylon |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE02Tecfi · 14 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics BE02
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 6–10 mm; length 40–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 02 06 040 | 6 | 40 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 4 | 45 |
| Tecfi BE 02 06 060 | 6 | 60 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 4 | 65 |
| Tecfi BE 02 06 080 | 6 | 80 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 4 | 85 |
| Tecfi BE 02 08 060 | 8 | 60 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 65 |
| Tecfi BE 02 08 080 | 8 | 80 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 85 |
| Tecfi BE 02 08 100 | 8 | 100 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 105 |
| Tecfi BE 02 08 120 | 8 | 120 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 125 |
| Tecfi BE 02 08 135 | 8 | 135 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 140 |
| Tecfi BE 02 10 060 | 10 | 60 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 65 |
| Tecfi BE 02 10 080 | 10 | 80 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 02 10 100 | 10 | 100 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 02 10 115 | 10 | 115 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 02 10 135 | 10 | 135 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 02 10 160 | 10 | 160 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 165 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE04Tecfi · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics BE04
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 04 08 080 | 8 | 80 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 85 |
| Tecfi BE 04 08 100 | 8 | 100 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 105 |
| Tecfi BE 04 08 120 | 8 | 120 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 5.5 | 125 |
| Tecfi BE 04 10 080 | 10 | 80 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 04 10 100 | 10 | 100 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 04 10 115 | 10 | 115 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 04 10 135 | 10 | 135 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 04 10 160 | 10 | 160 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 165 |
| Tecfi BE 04 10 200 | 10 | 200 | Impronta a Croce tipo Z | Nylon / Acciaio | Zinc plated | 7 | 205 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE08Tecfi · 10 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics BE08
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 60–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 08 08 060 | 8 | 60 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 65 |
| Tecfi BE 08 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 85 |
| Tecfi BE 08 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 105 |
| Tecfi BE 08 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 125 |
| Tecfi BE 08 08 135 | 8 | 135 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 140 |
| Tecfi BE 08 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 08 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 08 10 115 | 10 | 115 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 08 10 135 | 10 | 135 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 08 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE09Tecfi · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics BE09
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 09 08 080 | 8 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 85 |
| Tecfi BE 09 08 100 | 8 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 105 |
| Tecfi BE 09 08 120 | 8 | 120 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 5.5 | 125 |
| Tecfi BE 09 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 09 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 09 10 115 | 10 | 115 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 09 10 135 | 10 | 135 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 09 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 |
| Tecfi BE 09 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 205 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE03Tecfi · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics BE03
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 60–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 03 08 060 | 8 | 60 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 65 |
| Tecfi BE 03 08 080 | 8 | 80 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 85 |
| Tecfi BE 03 08 100 | 8 | 100 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 105 |
| Tecfi BE 03 08 120 | 8 | 120 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 125 |
| Tecfi BE 03 08 135 | 8 | 135 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 140 |
| Tecfi BE 03 10 060 | 10 | 60 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 65 |
| Tecfi BE 03 10 080 | 10 | 80 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 03 10 100 | 10 | 100 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 03 10 115 | 10 | 115 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 03 10 135 | 10 | 135 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 03 10 160 | 10 | 160 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 165 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE05Tecfi · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics BE05
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 8–10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 05 08 080 | 8 | 80 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 85 |
| Tecfi BE 05 08 100 | 8 | 100 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 105 |
| Tecfi BE 05 08 120 | 8 | 120 | Chiave | Nylon / Acciaio | Zinc plated | 5.5 | 125 |
| Tecfi BE 05 10 080 | 10 | 80 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 05 10 100 | 10 | 100 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 05 10 115 | 10 | 115 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 05 10 135 | 10 | 135 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 05 10 160 | 10 | 160 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 165 |
| Tecfi BE 05 10 200 | 10 | 200 | Chiave | Nylon / Acciaio | Zinc plated | 7 | 205 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE10Tecfi · 6 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics BE10
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 10 mm; length 60–160 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 10 10 060 | 10 | 60 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 65 |
| Tecfi BE 10 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 10 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 10 10 115 | 10 | 115 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 10 10 135 | 10 | 135 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 10 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
BE11Tecfi · 6 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics BE11
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 10 mm; length 80–200 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls |
|---|---|---|---|---|---|---|---|
| Tecfi BE 11 10 080 | 10 | 80 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 85 |
| Tecfi BE 11 10 100 | 10 | 100 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 105 |
| Tecfi BE 11 10 115 | 10 | 115 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 120 |
| Tecfi BE 11 10 135 | 10 | 135 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 140 |
| Tecfi BE 11 10 160 | 10 | 160 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 165 |
| Tecfi BE 11 10 200 | 10 | 200 | Impronta a 6 lobi | Nylon / Acciaio | Zinc plated | 7 | 205 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
HH00Tecfi · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics HH00
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon.
Documented series dimensions: nominal Ø 12–16 mm; length 100–240 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Material |
|---|---|---|---|
| Tecfi HH 00 12 160 | 12 | 160 | Nylon |
| Tecfi HH 00 12 200 | 12 | 200 | Nylon |
| Tecfi HH 00 12 240 | 12 | 240 | Nylon |
| Tecfi HH 00 14 100 | 14 | 100 | — |
| Tecfi HH 00 14 130 | 14 | 130 | — |
| Tecfi HH 00 16 140 | 16 | 140 | Nylon |
| Tecfi HH 00 16 160 | 16 | 160 | Nylon |
| Tecfi HH 00 16 200 | 16 | 200 | Nylon |
| Tecfi HH 00 16 240 | 16 | 240 | Nylon |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
HH01Tecfi · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics HH01
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Nylon, Steel.
Documented series dimensions: nominal Ø 12–16 mm; length 100–240 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor body Ø (mm) | Anchor length (mm) | Drive | Material | Finish | Diameter vite Øs | Length vite Ls | Length L (mm) |
|---|---|---|---|---|---|---|---|---|
| Tecfi HH 01 12 160 | 12 | 160 | Chiave | Nylon / Acciaio | Zinc plated | 10 | 160 | — |
| Tecfi HH 01 12 200 | 12 | 200 | Chiave | Nylon / Acciaio | Zinc plated | 10 | 200 | — |
| Tecfi HH 01 12 240 | 12 | 240 | Chiave | Nylon / Acciaio | Zinc plated | 10 | 240 | — |
| Tecfi HH 01 14 100 | 14 | 100 | Chiave | Steel | Zinc plated | 10 | 110 | 25 |
| Tecfi HH 01 14 130 | 14 | 130 | Chiave | Steel | Zinc plated | 10 | 140 | 30 |
| Tecfi HH 01 16 140 | 16 | 140 | Chiave | Nylon / Acciaio | Zinc plated | 12 | 150 | — |
| Tecfi HH 01 16 160 | 16 | 160 | Chiave | Nylon / Acciaio | Zinc plated | 12 | 170 | — |
| Tecfi HH 01 16 200 | 16 | 200 | Chiave | Nylon / Acciaio | Zinc plated | 12 | 210 | — |
| Tecfi HH 01 16 240 | 16 | 240 | Chiave | Nylon / Acciaio | Zinc plated | 12 | 250 | — |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-S-8VEJOT · 8 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics SDF-S-8V
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Steel.
Documented series dimensions: length 80–220 mm; thread Ø 8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8569080430 | 8.0 | Acciaio al carbonio | 80.0 | 30.0 |
| EJOT 8569100430 | 8.0 | Acciaio al carbonio | 100.0 | 50.0 |
| EJOT 8569120430 | 8.0 | Acciaio al carbonio | 120.0 | 70.0 |
| EJOT 8569140430 | 8.0 | Acciaio al carbonio | 140.0 | 90.0 |
| EJOT 8569160430 | 8.0 | Acciaio al carbonio | 160.0 | 110.0 |
| EJOT 8569180430 | 8.0 | Acciaio al carbonio | 180.0 | 130.0 |
| EJOT 8569200430 | 8.0 | Acciaio al carbonio | 200.0 | 150.0 |
| EJOT 8569220430 | 8.0 | Acciaio al carbonio | 220.0 | 170.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-KB-8VEJOT · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head.Full description and technical table ↓

Series characteristics SDF-KB-8V
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head.
Materials represented by the variants: Steel.
Documented series dimensions: length 60–220 mm; thread Ø 8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8570060430 | 8.0 | Acciaio al carbonio | 60.0 | 10.0 |
| EJOT 8570080430 | 8.0 | Acciaio al carbonio | 80.0 | 30.0 |
| EJOT 8570100430 | 8.0 | Acciaio al carbonio | 100.0 | 50.0 |
| EJOT 8570120430 | 8.0 | Acciaio al carbonio | 120.0 | 70.0 |
| EJOT 8570140430 | 8.0 | Acciaio al carbonio | 140.0 | 90.0 |
| EJOT 8570160430 | 8.0 | Acciaio al carbonio | 160.0 | 110.0 |
| EJOT 8570180430 | 8.0 | Acciaio al carbonio | 180.0 | 130.0 |
| EJOT 8570200430 | 8.0 | Acciaio al carbonio | 200.0 | 150.0 |
| EJOT 8570220430 | 8.0 | Acciaio al carbonio | 220.0 | 170.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-S-10VEJOT · 11 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics SDF-S-10V
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Documented series dimensions: length 50–220 mm; thread Ø 10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry, Perforated masonry. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Length (mm) | Spessore serrabile (calcestruzzo) B ≥ | Spessore serrabile (muratura) B ≤ |
|---|---|---|---|---|---|
| EJOT 8580050450 | 10.0 | Zinc plated | 50.0 | 10.0 | 0.0 |
| EJOT 8580060450 | 10.0 | Zinc plated | 60.0 | 20.0 | 10.0 |
| EJOT 8580070450 | 10.0 | Zinc plated | 70.0 | 30.0 | 20.0 |
| EJOT 8580080450 | 10.0 | Zinc plated | 80.0 | 40.0 | 30.0 |
| EJOT 8580100450 | 10.0 | Zinc plated | 100.0 | 60.0 | 50.0 |
| EJOT 8580120450 | 10.0 | Zinc plated | 120.0 | 80.0 | 70.0 |
| EJOT 8580140450 | 10.0 | Zinc plated | 140.0 | 100.0 | 90.0 |
| EJOT 8580160450 | 10.0 | Zinc plated | 160.0 | 120.0 | 110.0 |
| EJOT 8580180450 | 10.0 | Zinc plated | 180.0 | 140.0 | 130.0 |
| EJOT 8580200450 | 10.0 | Zinc plated | 200.0 | 160.0 | 150.0 |
| EJOT 8580220450 | 10.0 | Zinc plated | 220.0 | 180.0 | 170.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-KB-10VEJOT · 14 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, six-lobe drive.Full description and technical table ↓

Series characteristics SDF-KB-10V
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, six-lobe drive.
Materials represented by the variants: Steel, Stainless A4.
Documented series dimensions: length 50–220 mm; thread Ø 10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry, Perforated masonry. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Length (mm) | Spessore serrabile (calcestruzzo) B ≥ | Spessore serrabile (muratura) B ≤ |
|---|---|---|---|---|---|
| EJOT 8581050450 | 10.0 | Acciaio al carbonio | 50.0 | 10.0 | 0.0 |
| EJOT 8581060450 | 10.0 | Acciaio al carbonio | 60.0 | 20.0 | 10.0 |
| EJOT 8581070450 | 10.0 | Acciaio al carbonio | 70.0 | 30.0 | 20.0 |
| EJOT 8581080450 | 10.0 | Acciaio al carbonio | 80.0 | 40.0 | 30.0 |
| EJOT 8581100450 | 10.0 | Acciaio al carbonio | 100.0 | 60.0 | 50.0 |
| EJOT 8581120450 | 10.0 | Acciaio al carbonio | 120.0 | 80.0 | 70.0 |
| EJOT 8581140450 | 10.0 | Acciaio al carbonio | 140.0 | 100.0 | 90.0 |
| EJOT 8581160450 | 10.0 | Acciaio al carbonio | 160.0 | 120.0 | 110.0 |
| EJOT 8581180450 | 10.0 | Acciaio al carbonio | 180.0 | 140.0 | 130.0 |
| EJOT 8581200450 | 10.0 | Acciaio al carbonio | 200.0 | 160.0 | 150.0 |
| EJOT 8581220450 | 10.0 | Acciaio al carbonio | 220.0 | 180.0 | 170.0 |
| EJOT 8581050650 | 10.0 | Acciao Inox A4 | 50.0 | 10.0 | 0.0 |
| EJOT 8581060650 | 10.0 | Acciao Inox A4 | 60.0 | 20.0 | 10.0 |
| EJOT 8581070650 | 10.0 | Acciao Inox A4 | 70.0 | 30.0 | 20.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-S-14AEJOT · 13 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics SDF-S-14A
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Steel.
Documented series dimensions: length 120–360 mm; thread Ø 14 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry, Perforated masonry, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Anchor length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8591120430 | 14.0 | Acciaio al carbonio | 120.0 | 50.0 |
| EJOT 8591140430 | 14.0 | Acciaio al carbonio | 140.0 | 70.0 |
| EJOT 8591160430 | 14.0 | Acciaio al carbonio | 160.0 | 90.0 |
| EJOT 8591180430 | 14.0 | Acciaio al carbonio | 180.0 | 110.0 |
| EJOT 8591200430 | 14.0 | Acciaio al carbonio | 200.0 | 130.0 |
| EJOT 8591220430 | 14.0 | Acciaio al carbonio | 220.0 | 150.0 |
| EJOT 8591240430 | 14.0 | Acciaio al carbonio | 240.0 | 170.0 |
| EJOT 8591260430 | 14.0 | Acciaio al carbonio | 260.0 | 190.0 |
| EJOT 8591280430 | 14.0 | Acciaio al carbonio | 280.0 | 210.0 |
| EJOT 8591300430 | 14.0 | Acciaio al carbonio | 300.0 | 230.0 |
| EJOT 8591320430 | 14.0 | Acciaio al carbonio | 320.0 | 250.0 |
| EJOT 8591340430 | 14.0 | Acciaio al carbonio | 340.0 | 270.0 |
| EJOT 8591360430 | 14.0 | Acciaio al carbonio | 360.0 | 290.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-KB-14AEJOT · 4 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head.Full description and technical table ↓

Series characteristics SDF-KB-14A
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head.
Materials represented by the variants: Steel, Stainless A4.
Documented series dimensions: length 80–100 mm; thread Ø 14 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry, Perforated masonry, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Anchor length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8590080430 | 14.0 | Acciaio al carbonio | 80.0 | 10.0 |
| EJOT 8590080630 | 14.0 | Acciao Inox A4 | 80.0 | 10.0 |
| EJOT 8590100430 | 14.0 | Acciaio al carbonio | 100.0 | 30.0 |
| EJOT 8590100630 | 14.0 | Acciao Inox A4 | 100.0 | 30.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-KB-10HEJOT · 16 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, six-lobe drive.Full description and technical table ↓

Series characteristics SDF-KB-10H
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, six-lobe drive.
Materials represented by the variants: Steel, Stainless A4.
Documented series dimensions: length 80–220 mm; thread Ø 10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry, Perforated masonry, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8513080420 | 10.0 | Acciaio al carbonio | 80.0 | 10.0 |
| EJOT 8513100420 | 10.0 | Acciaio al carbonio | 100.0 | 30.0 |
| EJOT 8513120420 | 10.0 | Acciaio al carbonio | 120.0 | 50.0 |
| EJOT 8513140420 | 10.0 | Acciaio al carbonio | 140.0 | 70.0 |
| EJOT 8513160420 | 10.0 | Acciaio al carbonio | 160.0 | 90.0 |
| EJOT 8513180420 | 10.0 | Acciaio al carbonio | 180.0 | 110.0 |
| EJOT 8513200420 | 10.0 | Acciaio al carbonio | 200.0 | 130.0 |
| EJOT 8513220420 | 10.0 | Acciaio al carbonio | 220.0 | 150.0 |
| EJOT 8513080620 | 10.0 | Acciao Inox A4 | 80.0 | 10.0 |
| EJOT 8513100620 | 10.0 | Acciao Inox A4 | 100.0 | 30.0 |
| EJOT 8513120620 | 10.0 | Acciao Inox A4 | 120.0 | 50.0 |
| EJOT 8513140620 | 10.0 | Acciao Inox A4 | 140.0 | 70.0 |
| EJOT 8513160620 | 10.0 | Acciao Inox A4 | 160.0 | 90.0 |
| EJOT 8513180620 | 10.0 | Acciao Inox A4 | 180.0 | 110.0 |
| EJOT 8513200620 | 10.0 | Acciao Inox A4 | 200.0 | 130.0 |
| EJOT 8513220620 | 10.0 | Acciao Inox A4 | 220.0 | 150.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-S-10HEJOT · 24 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics SDF-S-10H
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Steel, Stainless A4.
Documented series dimensions: length 80–300 mm; thread Ø 10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry, Perforated masonry, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8510080420 | 10.0 | Acciaio al carbonio | 80.0 | 10.0 |
| EJOT 8510100420 | 10.0 | Acciaio al carbonio | 100.0 | 30.0 |
| EJOT 8510120420 | 10.0 | Acciaio al carbonio | 120.0 | 50.0 |
| EJOT 8510140420 | 10.0 | Acciaio al carbonio | 140.0 | 70.0 |
| EJOT 8510160420 | 10.0 | Acciaio al carbonio | 160.0 | 90.0 |
| EJOT 8510180420 | 10.0 | Acciaio al carbonio | 180.0 | 110.0 |
| EJOT 8510200420 | 10.0 | Acciaio al carbonio | 200.0 | 130.0 |
| EJOT 8510220420 | 10.0 | Acciaio al carbonio | 220.0 | 150.0 |
| EJOT 8510240420 | 10.0 | Acciaio al carbonio | 240.0 | 170.0 |
| EJOT 8510260420 | 10.0 | Acciaio al carbonio | 260.0 | 190.0 |
| EJOT 8510280420 | 10.0 | Acciaio al carbonio | 280.0 | 210.0 |
| EJOT 8510300420 | 10.0 | Acciaio al carbonio | 300.0 | 230.0 |
| EJOT 8510080620 | 10.0 | Acciao Inox A4 | 80.0 | 10.0 |
| EJOT 8510100620 | 10.0 | Acciao Inox A4 | 100.0 | 30.0 |
| EJOT 8510120620 | 10.0 | Acciao Inox A4 | 120.0 | 50.0 |
| EJOT 8510140620 | 10.0 | Acciao Inox A4 | 140.0 | 70.0 |
| EJOT 8510160620 | 10.0 | Acciao Inox A4 | 160.0 | 90.0 |
| EJOT 8510180620 | 10.0 | Acciao Inox A4 | 180.0 | 110.0 |
| EJOT 8510200620 | 10.0 | Acciao Inox A4 | 200.0 | 130.0 |
| EJOT 8510220620 | 10.0 | Acciao Inox A4 | 220.0 | 150.0 |
| EJOT 8510240620 | 10.0 | Acciao Inox A4 | 240.0 | 170.0 |
| EJOT 8510260620 | 10.0 | Acciao Inox A4 | 260.0 | 190.0 |
| EJOT 8510280620 | 10.0 | Acciao Inox A4 | 280.0 | 210.0 |
| EJOT 8510300620 | 10.0 | Acciao Inox A4 | 300.0 | 230.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDP-S-10GEJOT · 15 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics SDP-S-10G
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Steel, Stainless A4.
Documented series dimensions: length 80–220 mm; thread Ø 10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Anchor length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8530080420 | 10.0 | Acciaio al carbonio | 80.0 | 10.0 |
| EJOT 8530080620 | 10.0 | Acciao Inox A4 | 80.0 | 10.0 |
| EJOT 8530100420 | 10.0 | Acciaio al carbonio | 100.0 | 30.0 |
| EJOT 8530100620 | 10.0 | Acciao Inox A4 | 100.0 | 30.0 |
| EJOT 8530120420 | 10.0 | Acciaio al carbonio | 120.0 | 50.0 |
| EJOT 8530120620 | 10.0 | Acciao Inox A4 | 120.0 | 50.0 |
| EJOT 8530140420 | 10.0 | Acciaio al carbonio | 140.0 | 70.0 |
| EJOT 8530140620 | 10.0 | Acciao Inox A4 | 140.0 | 70.0 |
| EJOT 8530160420 | 10.0 | Acciaio al carbonio | 160.0 | 90.0 |
| EJOT 8530160620 | 10.0 | Acciao Inox A4 | 160.0 | 90.0 |
| EJOT 8530180420 | 10.0 | Acciaio al carbonio | 180.0 | 110.0 |
| EJOT 8530180620 | 10.0 | Acciao Inox A4 | 180.0 | 110.0 |
| EJOT 8530200420 | 10.0 | Acciaio al carbonio | 200.0 | 130.0 |
| EJOT 8530220420 | 10.0 | Acciaio al carbonio | 220.0 | 150.0 |
| EJOT 8530220620 | 10.0 | Acciao Inox A4 | 220.0 | 150.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDP-KB-10GEJOT · 16 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, six-lobe drive.Full description and technical table ↓

Series characteristics SDP-KB-10G
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: hexagonal head, six-lobe drive.
Materials represented by the variants: Steel, Stainless A4.
Documented series dimensions: length 80–220 mm; thread Ø 10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material | Anchor length (mm) | Fixture thickness B ≥ (mm) |
|---|---|---|---|---|
| EJOT 8532080420 | 10.0 | Acciaio al carbonio | 80.0 | 10.0 |
| EJOT 8532100420 | 10.0 | Acciaio al carbonio | 100.0 | 30.0 |
| EJOT 8532120420 | 10.0 | Acciaio al carbonio | 120.0 | 50.0 |
| EJOT 8532140420 | 10.0 | Acciaio al carbonio | 140.0 | 70.0 |
| EJOT 8532160420 | 10.0 | Acciaio al carbonio | 160.0 | 90.0 |
| EJOT 8532180420 | 10.0 | Acciaio al carbonio | 180.0 | 110.0 |
| EJOT 8532200420 | 10.0 | Acciaio al carbonio | 200.0 | 130.0 |
| EJOT 8532080620 | 10.0 | Acciao Inox A4 | 80.0 | 10.0 |
| EJOT 8532100620 | 10.0 | Acciao Inox A4 | 100.0 | 30.0 |
| EJOT 8532120620 | 10.0 | Acciao Inox A4 | 120.0 | 50.0 |
| EJOT 8532140620 | 10.0 | Acciao Inox A4 | 140.0 | 70.0 |
| EJOT 8532160620 | 10.0 | Acciao Inox A4 | 160.0 | 90.0 |
| EJOT 8532180620 | 10.0 | Acciao Inox A4 | 180.0 | 110.0 |
| EJOT 8532200620 | 10.0 | Acciao Inox A4 | 200.0 | 130.0 |
| EJOT 8532220420 | 10.0 | Acciao Inox A4 | 220.0 | 150.0 |
| EJOT 8532220620 | 10.0 | Acciao Inox A4 | 220.0 | 150.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDP-S-10SEJOT · 1 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics SDP-S-10S
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Stainless A2.
Documented series dimensions: thread Ø 10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Material |
|---|---|---|
| EJOT 8774120423 | 10.0 | Acciao Inox A2 |
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Tassello ad espansione VSD 8U-EEJOT · 6 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics Tassello ad espansione VSD 8U-E
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Materials represented by the variants: Stainless A4.
Documented series dimensions: length 205–305 mm; thread Ø 8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Masonry, Perforated masonry. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Thread Ø (mm) | Distanza | Length (mm) |
|---|---|---|---|
| EJOT 8765205600 | 8.0 | 0.0 | 205.0 |
| EJOT 8765225600 | 8.0 | 20.0 | 225.0 |
| EJOT 8765245600 | 8.0 | 40.0 | 245.0 |
| EJOT 8765265600 | 8.0 | 60.0 | 265.0 |
| EJOT 8765285600 | 8.0 | 80.0 | 285.0 |
| EJOT 8765305600 | 8.0 | 100.0 | 305.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
SDF-S plus 8UBEJOT · 9 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics SDF-S plus 8UB
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Documented series dimensions: nominal Ø 8 mm; length 0–280 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Masonry, Perforated masonry, Aerated concrete. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Anchor Ø (mm) | Length (mm) | Anchorage depth (mm) | Activation method | Material |
|---|---|---|---|---|---|
| EJOT 8786100460 | 8.0 | 100.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786120460 | 8.0 | 120.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786140460 | 8.0 | 140.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786160460 | 8.0 | 160.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786180460 | 8.0 | 180.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786200460 | 8.0 | 200.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786220460 | 8.0 | 220.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786240460 | 8.0 | 0.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
| EJOT 8786280460 | 8.0 | 280.0 | 70.0 | Fissaggio ad avvitamento | Zinc plated |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSD 8U-VEJOT · 1 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.Full description and technical table ↓

Series characteristics VSD 8U-V
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers.
Materials represented by the variants: Steel.
Documented series dimensions: length 225 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.
Substrates mentioned in the series sources: Concrete, Masonry, Perforated masonry, Aerated concrete, Insulation. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source | Length (mm) | Spessore minimo lamiera esterna | Distanza interno/esterno | Anchorage depth (mm) | Hole depth |
|---|---|---|---|---|---|
| EJOT 8765225400 | 225.0 | 115.0 | 20.0 - 40.0 | 70.0 | 80.0 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
VSD 2G 8U-VEJOT · 7 referencesLong fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.Full description and technical table ↓

Series characteristics VSD 2G 8U-V
Long fixing passing through the fixture to reach the load-bearing substrate. Its active zone must extend beyond non-load-bearing layers. Series design: six-lobe drive.
Substrates mentioned in the series sources: Masonry, Perforated masonry. Check the application scope for the individual part.
Compare total length, fixture thickness, anchorage depth and drill hole. For facades and redundant non-structural fixings, check the scope of the specific ETA, substrate and screw configuration.
The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.
View the manufacturer’s product page ↗Part-specific technical table
Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.
| Part number and source |
|---|
| EJOT 8502145400 |
| EJOT 8502205400 |
| EJOT 8502225400 |
| EJOT 8502245400 |
| EJOT 8502265400 |
| EJOT 8502285400 |
| EJOT 8502305400 |
System documents
ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.
Anchor finder
Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.
Request technical review or a quotation
Select a finder reference or describe the application.
FAQ
How do I select an anchor?
Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.
Does equal diameter mean equal capacity?
No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.
Do all anchors have an ETA and CE marking?
These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.
What information is needed for an enquiry?
Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.
Sources and documentation
Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.
Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.