Industrial fixings · Dueemme Sidol

Insulation and ETICS anchors

ETICS anchors pass through the insulation into the load-bearing substrate. Plate, expansion element and installation method form part of the system configuration.

Tecfi ZZE01 · Insulation and ETICS anchors
Family example · Tecfi ZZE01

Features and selection criteria

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Designs, materials and substrates

This family contains 12 series or reference groups, with 102 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.

Documented materials

Other polymers · Nylon · Steel

Substrates mentioned in the sources

Concrete · Masonry · Aerated concrete · Insulation · Perforated masonry

This list describes the family and does not assign every substrate to every variant.

Information to define before selection

ParameterWhat to check
Load-bearing substrateMaterial type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size.
Fixing geometryTotal length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers.
Depth and distancesCompare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity.
Environment and exposureCheck material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment.
Loads and documentationDefine action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification.

Installation sequence to verify

  1. Identify substrate category, insulation and assembly thickness.
  2. Select length and anchorage depth allowing for non-load-bearing layers.
  3. Use flush or recessed installation only where permitted by the design and system.
  4. Check plate bearing, fixing layout and specified surface treatment.

This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.

Series and technical tables

Tecfi BN01 · Insulation and ETICS anchorsBN01Tecfi · 5 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
Tecfi BN01 · Insulation and ETICS anchors
Series reference image · Tecfi

Series characteristics BN01

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Materials represented by the variants: Other polymers.

Documented series dimensions: nominal Ø 8 mm; length 50–130 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi BN01 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)MaterialDrill Ø d₀ (mm)Tfix (spess. fissabile) MINTfix (spess. fissabile) MAX
Tecfi BN 01 08 050850Polypropylene81020 -
Tecfi BN 01 08 070870Polypropylene82040 -
Tecfi BN 01 08 085885Polypropylene84060 -
Tecfi BN 01 08 1108110Polypropylene86080 -
Tecfi BN 01 08 1308130Polypropylene880100 -

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi ZZE01 · Insulation and ETICS anchorsZZE01Tecfi · 8 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.Full description and technical table ↓
Tecfi ZZE01 · Insulation and ETICS anchors
Series reference image · Tecfi

Series characteristics ZZE01

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.

Materials represented by the variants: Nylon, Other polymers.

Documented series dimensions: nominal Ø 10 mm; length 70–240 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi ZZE01 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)MaterialFixture thickness max (mm)Part-specific documentation indicators
Tecfi ZZE 01 10 0701070HDPE / Nylon30ETA-CE
Tecfi ZZE 01 10 0901090HDPE / Nylon50ETA-CE
Tecfi ZZE 01 10 11010110HDPE / Nylon70ETA-CE
Tecfi ZZE 01 10 13010130HDPE / Nylon90ETA-CE
Tecfi ZZE 01 10 15010150HDPE / Nylon110ETA-CE
Tecfi ZZE 01 10 18010180HDPE / Nylon140ETA-CE
Tecfi ZZE 01 10 21010210HDPE / Nylon170ETA-CE
Tecfi ZZE 01 10 24010240HDPE / Nylon200ETA-CE

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi ZZE21 · Insulation and ETICS anchorsZZE21Tecfi · 8 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.Full description and technical table ↓
Tecfi ZZE21 · Insulation and ETICS anchors
Series reference image · Tecfi

Series characteristics ZZE21

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.

Materials represented by the variants: Other polymers, Steel.

Documented series dimensions: nominal Ø 10 mm; length 70–240 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi ZZE21 · dimensional and installation characteristics
Part number and sourceAnchor body Ø (mm)Anchor length (mm)MaterialFinishFixture thickness max (mm)Part-specific documentation indicators
Tecfi ZZE 21 10 0701070HDPE / AcciaioZinc plated30ETA-CE
Tecfi ZZE 21 10 0901090HDPE / AcciaioZinc plated50ETA-CE
Tecfi ZZE 21 10 11010110HDPE / AcciaioZinc plated70ETA-CE
Tecfi ZZE 21 10 13010130HDPE / AcciaioZinc plated90ETA-CE
Tecfi ZZE 21 10 15010150HDPE / AcciaioZinc plated110ETA-CE
Tecfi ZZE 21 10 18010180HDPE / AcciaioZinc plated140ETA-CE
Tecfi ZZE 21 10 21010210HDPE / AcciaioZinc plated170ETA-CE
Tecfi ZZE 21 10 24010240HDPE / AcciaioZinc plated200ETA-CE

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi ZZER01 · Insulation and ETICS anchorsZZER01Tecfi · 1 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
Tecfi ZZER01 · Insulation and ETICS anchors
Series reference image · Tecfi

Series characteristics ZZER01

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Materials represented by the variants: Other polymers.

Documented series dimensions: nominal Ø 90 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi ZZER01 · dimensional and installation characteristics
Part number and sourceDisc Ø (mm)MaterialPart-specific documentation indicators
Tecfi ZZER 01 10 09090HDPEETA-CE

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT ejotherm® H2 · Insulation and ETICS anchorsejotherm® H2EJOT · 11 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.Full description and technical table ↓
EJOT ejotherm® H2 · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics ejotherm® H2

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.

Materials represented by the variants: Other polymers, Steel.

Documented series dimensions: nominal Ø 8 mm; length 95–295 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Masonry, Aerated concrete, Insulation. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT ejotherm® H2 · dimensional and installation characteristics
Part number and sourcePlate/washer Ø (mm)Anchor Ø (mm)Length (mm)
EJOT 852809526060.08.095.0
EJOT 852811526060.08.0115.0
EJOT 852813526060.08.0135.0
EJOT 852815526060.08.0155.0
EJOT 852817526060.08.0175.0
EJOT 852819526060.08.0195.0
EJOT 852821526060.08.0215.0
EJOT 852823526060.08.0235.0
EJOT 852825526060.08.0255.0
EJOT 852827526060.08.0275.0
EJOT 852829526060.08.0295.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT ejotherm® H1 · Insulation and ETICS anchorsejotherm® H1EJOT · 14 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.Full description and technical table ↓
EJOT ejotherm® H1 · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics ejotherm® H1

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration. Series design: nail activation.

Materials represented by the variants: Other polymers, Steel.

Documented series dimensions: nominal Ø 8 mm; length 95–355 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Masonry, Aerated concrete, Insulation. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT ejotherm® H1 · dimensional and installation characteristics
Part number and sourcePlate/washer Ø (mm)Anchor Ø (mm)Length (mm)
EJOT 874409540060.08.095.0
EJOT 874411540060.08.0115.0
EJOT 874413540060.08.0135.0
EJOT 874415540060.08.0155.0
EJOT 874417540060.08.0175.0
EJOT 874419540060.08.0195.0
EJOT 874421540060.08.0215.0
EJOT 874423540060.08.0235.0
EJOT 874425540060.08.0255.0
EJOT 874427540060.08.0275.0
EJOT 874429540060.08.0295.0
EJOT 874431540060.08.0315.0
EJOT 874433540060.08.0335.0
EJOT 874435540060.08.0355.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT ejotherm® S1 short · Insulation and ETICS anchorsejotherm® S1 shortEJOT · 3 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
EJOT ejotherm® S1 short · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics ejotherm® S1 short

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Documented series dimensions: length 60–100 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Insulation. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT ejotherm® S1 short · dimensional and installation characteristics
Part number and sourceLength (mm)
EJOT 871506057060.0
EJOT 871508057080.0
EJOT 8715100570100.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT H3 · Insulation and ETICS anchorsH3EJOT · 9 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
EJOT H3 · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics H3

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Materials represented by the variants: Nylon.

Documented series dimensions: nominal Ø 8 mm; length 75–235 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Masonry, Perforated masonry. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT H3 · dimensional and installation characteristics
Part number and sourcePlate/washer Ø (mm)Anchor Ø (mm)Length (mm)Activation method
EJOT 857307510060.08.075.0Fissaggio a percussione
EJOT 857309510060.08.095.0Fissaggio a percussione
EJOT 857311510060.08.0115.0Fissaggio a percussione
EJOT 857313510060.08.0135.0Fissaggio a percussione
EJOT 857315510060.08.0155.0Fissaggio a percussione
EJOT 857317510060.08.0175.0Fissaggio a percussione
EJOT 857319510060.08.0195.0Fissaggio a percussione
EJOT 857321510060.08.0215.0Fissaggio a percussione
EJOT 857323510060.08.0235.0Fissaggio a percussione

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT ejotherm® STR U 2G · Insulation and ETICS anchorsejotherm® STR U 2GEJOT · 17 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
EJOT ejotherm® STR U 2G · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics ejotherm® STR U 2G

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Materials represented by the variants: Steel.

Documented series dimensions: nominal Ø 8 mm; length 115–455 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Masonry, Aerated concrete, Insulation. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT ejotherm® STR U 2G · dimensional and installation characteristics
Part number and sourcePlate/washer Ø (mm)Anchor Ø (mm)Length (mm)FissaggioTolleranzaActivation methodMaterial
EJOT 871911540060.08.0115.0Montaggio a filo e ad incasso3.0Fissaggio ad avvitamentoAcciaio al carbonio
EJOT 871913540060.08.0135.0Montaggio a filo e ad incasso solo montaggio a filo10.0 30.0 50.0Fissaggio ad avvitamentoAcciaio al carbonio
EJOT 871915540060.08.0155.0Montaggio a filo e ad incasso solo montaggio a filo10.0 30.0 50.0 70.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871917540060.08.0175.0Montaggio a filo e ad incasso solo montaggio a filo10.0 30.0 70.0Fissaggio ad avvitamentoAcciaio al carbonio
EJOT 871919540060.08.0195.0solo montaggio a filo Montaggio a filo e ad incasso10.0 30.0 50.0 70.0 90.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871921540060.08.0215.0solo montaggio a filo Montaggio a filo e ad incasso10.0 30.0 50.0 70.0 90.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871923540060.08.0235.0Montaggio a filo e ad incasso10.0 30.0 50.0 70.0 90.0 110.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871925540060.08.0255.0Montaggio a filo e ad incasso10.0 30.0 50.0 70.0 90.0 110.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871927540060.08.0275.0solo montaggio a filo Montaggio a filo e ad incasso90.0 110.0 70.0 50.0 30.0 10.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871929540060.08.0295.0solo montaggio a filo Montaggio a filo e ad incasso10.0 30.0 50.0 70.0 90.0 110.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871931540060.08.0315.0solo montaggio a filo Montaggio a filo e ad incasso10.0 30.0 50.0 70.0 90.0 110.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871935540060.08.0355.0Montaggio a filo e ad incasso10.0 30.0 50.0 70.0 90.0 110.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871937540060.08.0375.0Montaggio a filo e ad incasso90.0 110.0 70.0 50.0 30.0 10.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871939540060.08.0395.0Montaggio a filo e ad incasso50.0 110.0 90.0 70.0 10.0 30.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871941540060.08.0415.0Montaggio a filo e ad incasso110.0 10.0 70.0 90.0 50.0 30.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871943540060.08.0435.0Montaggio a filo e ad incasso30.0 90.0 50.0 70.0 10.0 110.0 show moreFissaggio ad avvitamentoAcciaio al carbonio
EJOT 871945540060.08.0455.0Montaggio a filo e ad incasso50.0 70.0 90.0 10.0 30.0 110.0 show moreFissaggio ad avvitamentoAcciaio al carbonio

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT ejotherm® S1 · Insulation and ETICS anchorsejotherm® S1EJOT · 19 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
EJOT ejotherm® S1 · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics ejotherm® S1

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Documented series dimensions: length 100–460 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Masonry, Perforated masonry, Aerated concrete, Insulation. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT ejotherm® S1 · dimensional and installation characteristics
Part number and sourceLength (mm)
EJOT 8715100540100.0
EJOT 8715120540120.0
EJOT 8715140540140.0
EJOT 8715160540160.0
EJOT 8715180540180.0
EJOT 8715200540200.0
EJOT 8715220540220.0
EJOT 8715240540240.0
EJOT 8715260540260.0
EJOT 8715280540280.0
EJOT 8715300540300.0
EJOT 8715320540320.0
EJOT 8715340540340.0
EJOT 8715360540360.0
EJOT 8715380540380.0
EJOT 8715400540400.0
EJOT 8715420540420.0
EJOT 8715440540440.0
EJOT 8715460540460.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT ejotherm® SDK U · Insulation and ETICS anchorsejotherm® SDK UEJOT · 4 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
EJOT ejotherm® SDK U · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics ejotherm® SDK U

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Documented series dimensions: nominal Ø 8 mm; length 45–105 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Masonry, Perforated masonry, Aerated concrete. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT ejotherm® SDK U · dimensional and installation characteristics
Part number and sourceAnchor Ø (mm)Length (mm)Activation methodAnchorage depth=25
EJOT 87980454008.045.0Fissaggio ad avvitamento20.0
EJOT 87980654008.065.0Fissaggio ad avvitamento40.0
EJOT 87980854008.085.0Fissaggio ad avvitamento60.0
EJOT 87981054008.0105.0Fissaggio ad avvitamento80.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT ejotherm® NK U · Insulation and ETICS anchorsejotherm® NK UEJOT · 3 referencesFixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.Full description and technical table ↓
EJOT ejotherm® NK U · Insulation and ETICS anchors
Series reference image · EJOT

Series characteristics ejotherm® NK U

Fixing or component connecting insulation board to the substrate. Length, plate and anchoring element must be assessed in the ETICS system configuration.

Documented series dimensions: nominal Ø 8 mm; length 45–85 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Perforated masonry, Aerated concrete. Check the application scope for the individual part.

Identify insulation type and thickness, non-load-bearing layers and substrate category. Anchor number and layout require ETICS-system and wind-action verification; plate diameter alone is insufficient.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT ejotherm® NK U · dimensional and installation characteristics
Part number and sourceAnchor Ø (mm)Length (mm)Activation method
EJOT 87970454008.045.0Fissaggio a percussione
EJOT 87970654008.065.0Fissaggio a percussione
EJOT 87970854008.085.0Fissaggio a percussione

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Anchor finder

Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.

Request technical review or a quotation

Select a finder reference or describe the application.

The summary is transferred to the contact form for your review and submission.

FAQ

How do I select an anchor?

Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.

Does equal diameter mean equal capacity?

No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.

Do all anchors have an ETA and CE marking?

These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.

What information is needed for an enquiry?

Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.

Sources and documentation

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Tecfi · EJOT

Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.

Dueemme Sidol
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.