Industrial fixings · Dueemme Sidol

Concrete and masonry screws

The anchor thread engages the substrate after the specified drilling operation. Nominal screw diameter, drill diameter and anchorage depth are separate quantities.

Tecfi HXE01 · Concrete and masonry screws
Family example · Tecfi HXE01

Features and selection criteria

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Designs, materials and substrates

This family contains 27 series or reference groups, with 347 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.

Documented materials

Steel · Stainless A4

Substrates mentioned in the sources

Concrete · Cracked concrete · Masonry

This list describes the family and does not assign every substrate to every variant.

Information to define before selection

ParameterWhat to check
Load-bearing substrateMaterial type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size.
Fixing geometryTotal length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers.
Depth and distancesCompare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity.
Environment and exposureCheck material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment.
Loads and documentationDefine action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification.

Installation sequence to verify

  1. Check pilot-hole diameter separately from thread diameter.
  2. Provide the depth and cleaning specified for the selected configuration.
  3. Install using the equipment and installation limits stated in the sheet.
  4. Check bearing, fixture thickness and anchorage depth without using generic torque values.

This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.

Series and technical tables

Tecfi HXE01 · Concrete and masonry screwsHXE01Tecfi · 40 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.Full description and technical table ↓
Tecfi HXE01 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE01

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–14 mm; length 40–400 mm; thread Ø 6–16 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE01 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 01 06 040540SteelZinc plated65——ETA-CE · EAD 330747-00-0601
Tecfi HXE 01 06 060560SteelZinc plated6255—ETA-CE · EAD 330747-00-0601
Tecfi HXE 01 06 080580SteelZinc plated64525—ETA-CE · EAD 330747-00-0601
Tecfi HXE 01 08 040640SteelZinc plated8——5ETA-CE · EAD 330747-00-0601
Tecfi HXE 01 08 050650SteelZinc plated85—15ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 08 065665SteelZinc plated820530ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 08 080680SteelZinc plated8352045ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 08 1006100SteelZinc plated8554065ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 08 1206120SteelZinc plated8756085ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 08 1406140SteelZinc plated89580105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 10 050850SteelZinc plated105——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 10 060860SteelZinc plated1015——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 10 080880SteelZinc plated103510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 10 1008100SteelZinc plated105530—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 10 1208120SteelZinc plated107550—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 10 1408140SteelZinc plated109570—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 10 1608160SteelZinc plated1011590—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 0601060SteelZinc plated125——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 0701070SteelZinc plated1215——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 0901090SteelZinc plated123510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 11010110SteelZinc plated125530—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 13010130SteelZinc plated127550—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 15010150SteelZinc plated129570—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 19010190SteelZinc plated12135110—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 21010210SteelZinc plated12155130—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 25010250SteelZinc plated12195170—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 29010290SteelZinc plated12235210—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 33010330——12275250—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 12 40010400——12345320—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 0751475SteelZinc plated1610——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 0901490SteelZinc plated1625——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 11514115SteelZinc plated16505—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 13014130SteelZinc plated166520—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 15014150SteelZinc plated168540—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 18014180SteelZinc plated1611570—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 22014220——16155110—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 26014260——16195150—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 30014300——16235190—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 35014350——16285240—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 01 16 40014400——16335290—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HX21 · Concrete and masonry screwsHX21Tecfi · 32 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.Full description and technical table ↓
Tecfi HX21 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HX21

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–14 mm; length 40–310 mm; thread Ø 6–16 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HX21 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness (mm) tfix, red3Fixture thickness tfix,red2 (mm)
Tecfi HX 21 06 045545SteelZinc plated65———
Tecfi HX 21 06 060560SteelZinc plated62010——
Tecfi HX 21 06 1005100SteelZinc plated66050——
Tecfi HX 21 06 1205120SteelZinc plated68070——
Tecfi HX 21 08 040640SteelZinc plated8——5—
Tecfi HX 21 08 045645SteelZinc plated8——105
Tecfi HX 21 08 050650SteelZinc plated8——1510
Tecfi HX 21 08 060660SteelZinc plated810—2520
Tecfi HX 21 08 080680SteelZinc plated830204540
Tecfi HX 21 08 1006100SteelZinc plated850406560
Tecfi HX 21 08 1206120SteelZinc plated870608580
Tecfi HX 21 08 1406140SteelZinc plated89080105100
Tecfi HX 21 10 060860SteelZinc plated1010———
Tecfi HX 21 10 080880SteelZinc plated103010——
Tecfi HX 21 10 1008100SteelZinc plated105030——
Tecfi HX 21 10 1208120SteelZinc plated107050——
Tecfi HX 21 10 1408140SteelZinc plated109070——
Tecfi HX 21 10 1608160SteelZinc plated1011090——
Tecfi HX 21 12 0701070SteelZinc plated1210———
Tecfi HX 21 12 0901090SteelZinc plated123010——
Tecfi HX 21 12 11010110SteelZinc plated125030——
Tecfi HX 21 12 13010130SteelZinc plated127050——
Tecfi HX 21 12 15010150SteelZinc plated129070——
Tecfi HX 01 12 29010290SteelZinc plated12230210——
Tecfi HX 01 12 31010310SteelZinc plated12250230——
Tecfi HX 21 14 0651265SteelZinc plated145———
Tecfi HX 21 14 0751275SteelZinc plated1415———
Tecfi HX 21 14 11012110SteelZinc plated145010——
Tecfi HX 21 14 13012130SteelZinc plated147030——
Tecfi HX 21 14 15012150SteelZinc plated149050——
Tecfi HX 21 16 0901490SteelZinc plated1610———
Tecfi HX 01 16 18014180SteelZinc plated1610070——

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi ON01 · Concrete and masonry screwsON01Tecfi · 2 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.Full description and technical table ↓
Tecfi ON01 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics ON01

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 6 mm; length 40–55 mm; thread Ø 8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi ON01 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)
Tecfi ON 01 06 08040640SteelZinc plated85—
Tecfi ON 01 06 08055655SteelZinc plated82010

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE41 · Concrete and masonry screwsHXE41Tecfi · 26 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.Full description and technical table ↓
Tecfi HXE41 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE41

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–14 mm; length 40–150 mm; thread Ø 6–16 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE41 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 41 06 040540SteelSteel Saver - 1000h - ZL65——ETA-CE · EAD 330747-00-0601
Tecfi HXE 41 06 060560SteelSteel Saver - 1000h - ZL6255—ETA-CE · EAD 330747-00-0601
Tecfi HXE 41 06 080580SteelSteel Saver - 1000h - ZL64525—ETA-CE · EAD 330747-00-0601
Tecfi HXE 41 08 040640SteelSteel Saver - 1000h - ZL8——5ETA-CE · EAD 330747-00-0601
Tecfi HXE 41 08 050650SteelSteel Saver - 1000h - ZL85—15ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 08 065665SteelSteel Saver - 1000h - ZL820530ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 08 080680SteelSteel Saver - 1000h - ZL8352045ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 08 1006100SteelSteel Saver - 1000h - ZL8554065ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 08 1206120SteelSteel Saver - 1000h - ZL8756085ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 08 1406140SteelSteel Saver - 1000h - ZL89580105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 10 050850SteelSteel Saver - 1000h - ZL105——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 10 060860SteelSteel Saver - 1000h - ZL1015——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 10 080880SteelSteel Saver - 1000h - ZL103510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 10 1008100SteelSteel Saver - 1000h - ZL105530—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 10 1208120SteelSteel Saver - 1000h - ZL107550—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 10 1408140SteelSteel Saver - 1000h - ZL109570—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 12 0601060SteelSteel Saver - 1000h - ZL125——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 12 0701070SteelSteel Saver - 1000h - ZL1215——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 12 0901090SteelSteel Saver - 1000h - ZL123510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 12 11010110SteelSteel Saver - 1000h - ZL125530—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 12 13010130SteelSteel Saver - 1000h - ZL127550—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 16 0751475SteelSteel Saver - 1000h - ZL1610——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 16 0901490SteelSteel Saver - 1000h - ZL1625——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 16 11514115SteelSteel Saver - 1000h - ZL16505—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 16 13014130SteelSteel Saver - 1000h - ZL166520—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 41 16 15014150SteelSteel Saver - 1000h - ZL168540—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HX41 · Concrete and masonry screwsHX41Tecfi · 8 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.Full description and technical table ↓
Tecfi HX41 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HX41

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 6–14 mm; length 60–150 mm; thread Ø 8–16 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HX41 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,red2 (mm)Fixture thickness (mm) tfix, red3
Tecfi HX 41 08 080680SteelSteel Saver - 1000h - ZL820304045
Tecfi HX 41 10 060860SteelSteel Saver - 1000h - ZL10—10——
Tecfi HX 41 10 080880SteelSteel Saver - 1000h - ZL101030——
Tecfi HX 41 12 0701070SteelSteel Saver - 1000h - ZL12—10——
Tecfi HX 41 12 11010110SteelSteel Saver - 1000h - ZL123050——
Tecfi HX 41 12 15010150SteelSteel Saver - 1000h - ZL127090——
Tecfi HX 41 14 0751275SteelSteel Saver - 1000h - ZL14—15——
Tecfi HX 41 16 0901490SteelSteel Saver - 1000h - ZL16—10——

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HX71 · Concrete and masonry screwsHX71Tecfi · 7 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.Full description and technical table ↓
Tecfi HX71 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HX71

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head, flanged bearing.

Materials represented by the variants: Stainless A4.

Documented series dimensions: drill Ø 8–10 mm; length 60–140 mm; thread Ø 10–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HX71 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)
Tecfi HX 71 10 060860Acciaio Inox A41015—
Tecfi HX 71 10 080880Acciaio Inox A4103510
Tecfi HX 71 10 1008100Acciaio Inox A4105530
Tecfi HX 71 10 1408140Acciaio Inox A4109570
Tecfi HX 71 12 0901090Acciaio Inox A4123510
Tecfi HX 71 12 11010110Acciaio Inox A4125530
Tecfi HX 71 12 13010130Acciaio Inox A4127550

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE07 · Concrete and masonry screwsHXE07Tecfi · 14 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
Tecfi HXE07 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE07

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–8 mm; length 37–74 mm; thread Ø 6–10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE07 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Misura dado di giunzione h (mm)Misura dado di giunzione M outMisura dado di giunzione SWPart-specific documentation indicators
Tecfi HXE 07 06 06037537SteelZinc plated618M610ETA-CE · EAD 330747-00-0601
Tecfi HXE 07 06 08037537SteelZinc plated618M810ETA-CE · EAD 330747-00-0601
Tecfi HXE 07 66 08037537SteelZinc plated630M6 / M813ETA-CE · EAD 330747-00-0601
Tecfi HXE 07 08 06037637SteelZinc plated830M613ETA-CE · EAD 330747-00-0601
Tecfi HXE 07 08 08037637SteelZinc plated824M813ETA-CE · EAD 330747-00-0601
Tecfi HXE 07 08 10037637SteelZinc plated824M1013ETA-CE · EAD 330747-00-0601
Tecfi HXE 07 88 10037637SteelZinc plated830M8 / M1013ETA-CE · EAD 330747-00-0601
Tecfi HXE 07 08 06062662SteelZinc plated830M613ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 07 08 08062662SteelZinc plated824M813ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 07 08 10062662SteelZinc plated824M1013ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 07 88 10062662SteelZinc plated830M8 / M1013ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 07 10 08074874SteelZinc plated1024M813ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 07 10 10074874SteelZinc plated1030M1017ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 07 10 12074874SteelZinc plated1030M1217ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE02 · Concrete and masonry screwsHXE02Tecfi · 10 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
Tecfi HXE02 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE02

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 6–10 mm; length 90–248 mm; thread Ø 8–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE02 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 02 08 090690SteelZinc plated8102535ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 08 1206120SteelZinc plated8405565ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 08 1606160SteelZinc plated88095105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 10 1058105SteelZinc plated101035—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 10 1258125SteelZinc plated103055—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 10 1958195SteelZinc plated10100125—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 12 11810118SteelZinc plated121035—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 12 13810138SteelZinc plated123055—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 12 20810208SteelZinc plated12100125—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 02 12 24810248SteelZinc plated12140165—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE12 · Concrete and masonry screwsHXE12Tecfi · 10 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
Tecfi HXE12 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE12

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 6–10 mm; length 90–248 mm; thread Ø 8–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE12 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 12 08 090690SteelZinc plated8102535ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 08 1206120SteelZinc plated8405565ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 08 1606160SteelZinc plated88095105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 10 1058105SteelZinc plated101035—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 10 1258125SteelZinc plated103055—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 10 1958195SteelZinc plated10100125—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 12 11810118SteelZinc plated121035—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 12 13810138SteelZinc plated123055—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 12 20810208SteelZinc plated12100125—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 12 12 24810248SteelZinc plated12140165—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE85 · Concrete and masonry screwsHXE85Tecfi · 10 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
Tecfi HXE85 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE85

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 6–10 mm; length 90–248 mm; thread Ø 8–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE85 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Part-specific documentation indicators
Tecfi HXE 85 08 090690SteelZinc plated8ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 08 1206120SteelZinc plated8ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 08 1606160SteelZinc plated8ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 10 1058105SteelZinc plated10ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 10 1258125SteelZinc plated10ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 10 1958195SteelZinc plated10ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 12 11810118SteelZinc plated12ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 12 13810138SteelZinc plated12ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 12 20810208SteelZinc plated12ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 85 12 24810248SteelZinc plated12ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXB02 · Concrete and masonry screwsHXB02Tecfi · 15 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
Tecfi HXB02 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXB02

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 6–10 mm; length 90–208 mm; thread Ø 8–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXB02 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness (mm) tfix
Tecfi HXB 02 08 090690SteelSteel Saver - 500h810
Tecfi HXB 02 08 1006100SteelSteel Saver - 500h820
Tecfi HXB 02 08 1206120SteelSteel Saver - 500h840
Tecfi HXB 02 08 1406140SteelSteel Saver - 500h860
Tecfi HXB 02 08 1606160SteelSteel Saver - 500h880
Tecfi HXB 02 10 1058105SteelSteel Saver - 500h1010
Tecfi HXB 02 10 1258125SteelSteel Saver - 500h1030
Tecfi HXB 02 10 1458145SteelSteel Saver - 500h1050
Tecfi HXB 02 10 1758175SteelSteel Saver - 500h1080
Tecfi HXB 02 10 1958195SteelSteel Saver - 500h10100
Tecfi HXB 02 12 11810118SteelSteel Saver - 500h1210
Tecfi HXB 02 12 13810138SteelSteel Saver - 500h1230
Tecfi HXB 02 12 15810158SteelSteel Saver - 500h1250
Tecfi HXB 02 12 18810188SteelSteel Saver - 500h1280
Tecfi HXB 02 12 20810208SteelSteel Saver - 500h12100

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE03 · Concrete and masonry screwsHXE03Tecfi · 20 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.Full description and technical table ↓
Tecfi HXE03 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE03

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–10 mm; length 45–180 mm; thread Ø 6–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE03 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 03 06 045545SteelZinc plated610——ETA-CE · EAD 330747-00-0601
Tecfi HXE 03 06 065565SteelZinc plated63010—ETA-CE · EAD 330747-00-0601
Tecfi HXE 03 06 080580SteelZinc plated64525—ETA-CE · EAD 330747-00-0601
Tecfi HXE 03 08 045645SteelZinc plated8——10ETA-CE · EAD 330747-00-0601
Tecfi HXE 03 08 055655SteelZinc plated810—20ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 08 070670SteelZinc plated8251035ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 08 1006100SteelZinc plated8554065ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 08 1406140SteelZinc plated89580105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 10 055855SteelZinc plated1010——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 10 065865SteelZinc plated1020——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 10 080880SteelZinc plated103510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 10 1008100SteelZinc plated105530—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 10 1208120SteelZinc plated107550—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 10 1608160SteelZinc plated1011590—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 12 0651065SteelZinc plated1210——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 12 0801080SteelZinc plated1225——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 12 0901090SteelZinc plated123510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 12 10010100SteelZinc plated124520—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 12 12010120SteelZinc plated126540—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 03 12 18010180SteelZinc plated12125100—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXS21 · Concrete and masonry screwsHXS21Tecfi · 2 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.Full description and technical table ↓
Tecfi HXS21 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXS21

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5 mm; length 60–120 mm; thread Ø 6 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXS21 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness (mm) tfix
Tecfi HXS 21 06 060560SteelZinc plated610
Tecfi HXS 21 06 1205120SteelZinc plated670

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXS01 · Concrete and masonry screwsHXS01Tecfi · 7 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.Full description and technical table ↓
Tecfi HXS01 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXS01

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–10 mm; length 80–160 mm; thread Ø 6–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXS01 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,std (mm)
Tecfi HXS 01 06 1005100SteelSteel Saver - 500h650
Tecfi HXS 01 10 080880SteelSteel Saver - 500h1010
Tecfi HXS 01 10 1008100SteelSteel Saver - 500h1030
Tecfi HXS 01 10 1208120SteelSteel Saver - 500h1050
Tecfi HXS 01 10 1608160SteelSteel Saver - 500h1090
Tecfi HXS 01 12 10010100SteelSteel Saver - 500h1220
Tecfi HXS 01 12 12010120SteelSteel Saver - 500h1240

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE43 · Concrete and masonry screwsHXE43Tecfi · 19 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.Full description and technical table ↓
Tecfi HXE43 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE43

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–10 mm; length 45–160 mm; thread Ø 6–12 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE43 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 43 06 045545SteelSteel Saver - 1000h - ZL610——ETA-CE · EAD 330747-00-0601
Tecfi HXE 43 06 065565SteelSteel Saver - 1000h - ZL63010—ETA-CE · EAD 330747-00-0601
Tecfi HXE 43 06 080580SteelSteel Saver - 1000h - ZL64525—ETA-CE · EAD 330747-00-0601
Tecfi HXE 43 08 045645SteelSteel Saver - 1000h - ZL8——10ETA-CE · EAD 330747-00-0601
Tecfi HXE 43 08 055655SteelSteel Saver - 1000h - ZL810—20ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 08 070670SteelSteel Saver - 1000h - ZL8251035ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 08 1006100SteelSteel Saver - 1000h - ZL8554065ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 08 1406140SteelSteel Saver - 1000h - ZL89580105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 10 055855SteelSteel Saver - 1000h - ZL1010——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 10 065865SteelSteel Saver - 1000h - ZL1020——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 10 080880SteelSteel Saver - 1000h - ZL103510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 10 1008100SteelSteel Saver - 1000h - ZL105530—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 10 1208120SteelSteel Saver - 1000h - ZL107550—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 10 1608160SteelSteel Saver - 1000h - ZL1011590—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 12 0651065SteelSteel Saver - 1000h - ZL1210——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 12 0801080SteelSteel Saver - 1000h - ZL1225——ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 12 0901090SteelSteel Saver - 1000h - ZL123510—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 12 10010100SteelSteel Saver - 1000h - ZL124520—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 43 12 12010120SteelSteel Saver - 1000h - ZL126540—ETA-CE · EAD 330232-01-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXT01 · Concrete and masonry screwsHXT01Tecfi · 8 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: six-lobe drive.Full description and technical table ↓
Tecfi HXT01 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXT01

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 6–8 mm; length 60–120 mm; thread Ø 8–10 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXT01 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)
Tecfi HXT 01 08 060660SteelSteel Saver - 500h810—
Tecfi HXT 01 08 080680SteelSteel Saver - 500h83020
Tecfi HXT 01 08 1006100SteelSteel Saver - 500h85040
Tecfi HXT 01 08 1206120SteelSteel Saver - 500h87060
Tecfi HXT 01 10 060860SteelSteel Saver - 500h1010—
Tecfi HXT 01 10 080880SteelSteel Saver - 500h103010
Tecfi HXT 01 10 1008100SteelSteel Saver - 500h105030
Tecfi HXT 01 10 1208120SteelSteel Saver - 500h107050

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE05 · Concrete and masonry screwsHXE05Tecfi · 11 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.Full description and technical table ↓
Tecfi HXE05 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE05

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–6 mm; length 30–140 mm; thread Ø 6–8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE05 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red2 (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Part-specific documentation indicators
Tecfi HX 05 06 030530SteelZinc plated64———
Tecfi HXE 05 06 040540SteelZinc plated6—5—ETA-CE · EAD 330747-00-0601
Tecfi HXE 05 06 060560SteelZinc plated6—255ETA-CE · EAD 330747-00-0601
Tecfi HXE 05 06 080580SteelZinc plated6—4525ETA-CE · EAD 330747-00-0601
Tecfi HXE 05 08 040640SteelZinc plated85——ETA-CE · EAD 330747-00-0601
Tecfi HXE 05 08 050650SteelZinc plated8155—ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 05 08 065665SteelZinc plated830205ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 05 08 080680SteelZinc plated8453520ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 05 08 1006100SteelZinc plated8655540ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 05 08 1206120SteelZinc plated8857560ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 05 08 1406140SteelZinc plated81059580ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE06 · Concrete and masonry screwsHXE06Tecfi · 14 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.Full description and technical table ↓
Tecfi HXE06 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE06

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–6 mm; length 40–160 mm; thread Ø 6–8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE06 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 06 06 040540SteelZinc plated65——ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 06 060560SteelZinc plated6255—ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 06 080580SteelZinc plated64525—ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 06 1005100SteelZinc plated66545—ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 06 1205120SteelZinc plated68565—ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 06 1405140SteelZinc plated610585—ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 06 1605160SteelZinc plated6125105—ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 08 040640SteelZinc plated8——5ETA-CE · EAD 330747-00-0601
Tecfi HXE 06 08 050650SteelZinc plated85—15ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 06 08 065665SteelZinc plated820530ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Tecfi HXE 06 08 080680SteelZinc plated8352045ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Tecfi HXE 06 08 1006100SteelZinc plated8554065ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Tecfi HXE 06 08 1206120SteelZinc plated8756085ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Tecfi HXE 06 08 1406140SteelZinc plated89580105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE45 · Concrete and masonry screwsHXE45Tecfi · 10 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.Full description and technical table ↓
Tecfi HXE45 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE45

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–6 mm; length 40–140 mm; thread Ø 6–8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE45 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 45 06 040540SteelSteel Saver - 1000h - ZL65——ETA-CE · EAD 330747-00-0601
Tecfi HXE 45 06 060560SteelSteel Saver - 1000h - ZL6255—ETA-CE · EAD 330747-00-0601
Tecfi HXE 45 06 080580SteelSteel Saver - 1000h - ZL64525—ETA-CE · EAD 330747-00-0601
Tecfi HXE 45 08 040640SteelSteel Saver - 1000h - ZL8——5ETA-CE · EAD 330747-00-0601
Tecfi HXE 45 08 050650SteelSteel Saver - 1000h - ZL85—15ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 45 08 065665SteelSteel Saver - 1000h - ZL820530ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 45 08 080680SteelSteel Saver - 1000h - ZL8352045ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 45 08 1006100SteelSteel Saver - 1000h - ZL8554065ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 45 08 1206120SteelSteel Saver - 1000h - ZL8756085ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 45 08 1406140SteelSteel Saver - 1000h - ZL89580105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi HXE46 · Concrete and masonry screwsHXE46Tecfi · 14 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.Full description and technical table ↓
Tecfi HXE46 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics HXE46

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: drill Ø 5–6 mm; length 40–160 mm; thread Ø 6–8 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi HXE46 · dimensional and installation characteristics
Part number and sourceDrill Ø d₀ (mm)Length L (mm)MaterialFinishThread Ø dth (mm)Fixture thickness tfix,red1 (mm)Fixture thickness tfix,std (mm)Fixture thickness tfix,red2 (mm)Part-specific documentation indicators
Tecfi HXE 46 06 040540SteelSteel Saver - 1000h - ZL65——ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 06 060560SteelSteel Saver - 1000h - ZL6255—ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 06 080580SteelSteel Saver - 1000h - ZL64525—ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 06 1005100SteelSteel Saver - 1000h - ZL66545—ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 06 1205120SteelSteel Saver - 1000h - ZL68565—ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 06 1405140SteelSteel Saver - 1000h - ZL610585—ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 06 1605160SteelSteel Saver - 1000h - ZL6125105—ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 08 040640SteelSteel Saver - 1000h - ZL8——5ETA-CE · EAD 330747-00-0601
Tecfi HXE 46 08 050650SteelSteel Saver - 1000h - ZL85—15ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 46 08 065665SteelSteel Saver - 1000h - ZL820530ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 46 08 080680SteelSteel Saver - 1000h - ZL8352045ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 46 08 1006100SteelSteel Saver - 1000h - ZL8554065ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 46 08 1206120SteelSteel Saver - 1000h - ZL8756085ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic
Tecfi HXE 46 08 1406140SteelSteel Saver - 1000h - ZL89580105ETA-CE · EAD 330232-01-0601
ETA-CE · EAD 330747-00-0601
R120 (TR 020)
Sisma / Seismic

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi GS01 · Concrete and masonry screwsGS01Tecfi · 16 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.Full description and technical table ↓
Tecfi GS01 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics GS01

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: countersunk head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: length 50–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi GS01 · dimensional and installation characteristics
Part number and sourceScrew Ø (mm)Length L (mm)DriveMaterialFinishPz Confezione
Tecfi GS 01 75 0507.550Impronta a 6 lobiSteelZinc plated47
Tecfi GS 01 75 0607.560Impronta a 6 lobiSteelZinc plated57
Tecfi GS 01 75 0707.570Impronta a 6 lobiSteelZinc plated67
Tecfi GS 01 75 0807.580Impronta a 6 lobiSteelZinc plated77
Tecfi GS 01 75 0907.590Impronta a 6 lobiSteelZinc plated87
Tecfi GS 01 75 1007.5100Impronta a 6 lobiSteelZinc plated97
Tecfi GS 01 75 1107.5110Impronta a 6 lobiSteelZinc plated107
Tecfi GS 01 75 1207.5120Impronta a 6 lobiSteelZinc plated117
Tecfi GS 01 75 1357.5135Impronta a 6 lobiSteelZinc plated132
Tecfi GS 01 75 1507.5150Impronta a 6 lobiSteelZinc plated147
Tecfi GS 01 75 1607.5160Impronta a 6 lobiSteelZinc plated157
Tecfi GS 01 75 1807.5180Impronta a 6 lobiSteelZinc plated177
Tecfi GS 01 75 2007.5200Impronta a 6 lobiSteelZinc plated197
Tecfi GS 01 75 2207.5220Impronta a 6 lobiSteelZinc plated217
Tecfi GS 01 75 2507.5250Impronta a 6 lobiSteelZinc plated247
Tecfi GS 01 75 3007.5300Impronta a 6 lobiSteelZinc plated297

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi GS02 · Concrete and masonry screwsGS02Tecfi · 23 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.Full description and technical table ↓
Tecfi GS02 · Concrete and masonry screws
Series reference image · Tecfi

Series characteristics GS02

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: cylindrical head, six-lobe drive.

Materials represented by the variants: Steel.

Documented series dimensions: length 50–300 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi GS02 · dimensional and installation characteristics
Part number and sourceScrew Ø (mm)Length L (mm)DriveMaterialFinishPz Confezione
Tecfi GS 02 50 052552Impronta a 6 lobiSteelZinc plated46
Tecfi GS 02 50 062562Impronta a 6 lobiSteelZinc plated56
Tecfi GS 02 50 072572Impronta a 6 lobiSteelZinc plated66
Tecfi GS 02 50 082582Impronta a 6 lobiSteelZinc plated76
Tecfi GS 02 50 092592Impronta a 6 lobiSteelZinc plated86
Tecfi GS 02 50 1025102Impronta a 6 lobiSteelZinc plated96
Tecfi GS 02 50 1125112Impronta a 6 lobiSteelZinc plated106
Tecfi GS 02 75 0507.550Impronta a 6 lobiSteelZinc plated47
Tecfi GS 02 75 0607.560Impronta a 6 lobiSteelZinc plated57
Tecfi GS 02 75 0707.570Impronta a 6 lobiSteelZinc plated67
Tecfi GS 02 75 0807.580Impronta a 6 lobiSteelZinc plated77
Tecfi GS 02 75 0907.590Impronta a 6 lobiSteelZinc plated87
Tecfi GS 02 75 1007.5100Impronta a 6 lobiSteelZinc plated97
Tecfi GS 02 75 1107.5110Impronta a 6 lobiSteelZinc plated107
Tecfi GS 02 75 1207.5120Impronta a 6 lobiSteelZinc plated117
Tecfi GS 02 75 1357.5135Impronta a 6 lobiSteelZinc plated132
Tecfi GS 02 75 1507.5150Impronta a 6 lobiSteelZinc plated147
Tecfi GS 02 75 1607.5160Impronta a 6 lobiSteelZinc plated157
Tecfi GS 02 75 1807.5180Impronta a 6 lobiSteelZinc plated177
Tecfi GS 02 75 2007.5200Impronta a 6 lobiSteelZinc plated197
Tecfi GS 02 75 2207.5220Impronta a 6 lobiSteelZinc plated217
Tecfi GS 02 75 2507.5250Impronta a 6 lobiSteelZinc plated247
Tecfi GS 02 75 3007.5300Impronta a 6 lobiSteelZinc plated297

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT JC6-D-7,5 · Concrete and masonry screwsJC6-D-7,5EJOT · 10 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head.Full description and technical table ↓
EJOT JC6-D-7,5 · Concrete and masonry screws
Series reference image · EJOT

Series characteristics JC6-D-7,5

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head.

Materials represented by the variants: Stainless A4.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT JC6-D-7,5 · dimensional and installation characteristics
Part number and sourceDrill Ø (mm)
EJOT 35510829916.0
EJOT 35511829916.0
EJOT 35512829916.0
EJOT 35513829916.0
EJOT 35514829916.0
EJOT 35515829916.0
EJOT 35516829916.0
EJOT 35517829916.0
EJOT 35518839916.0
EJOT 35519829916.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT JC6-KB vite per calcestruzzo in acciaio inox A4 · Concrete and masonry screwsJC6-KB vite per calcestruzzo in acciaio inox A4EJOT · 11 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
EJOT JC6-KB vite per calcestruzzo in acciaio inox A4 · Concrete and masonry screws
Series reference image · EJOT

Series characteristics JC6-KB vite per calcestruzzo in acciaio inox A4

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Stainless A4.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT JC6-KB vite per calcestruzzo in acciaio inox A4 · dimensional and installation characteristics
Part number and sourceEmbedmentdepth h nom ≥drill hole depth h 1Drill Ø (mm)
EJOT 965007197045556.0
EJOT 965007197145/5555/656.0
EJOT 965007197245/5555/656.0
EJOT 965007197345/5555/656.0
EJOT 965007197850608.0
EJOT 965007197450/6560/758.0
EJOT 965007197550/6560/758.0
EJOT 965007197650/6560/758.0
EJOT 965007193355/8565/9510.0
EJOT 965007193455/8565/9510.0
EJOT 965007193555/8565/9510.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT Vite per calcestruzzo JC2-IT · Concrete and masonry screwsVite per calcestruzzo JC2-ITEJOT · 1 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head.Full description and technical table ↓
EJOT Vite per calcestruzzo JC2-IT · Concrete and masonry screws
Series reference image · EJOT

Series characteristics Vite per calcestruzzo JC2-IT

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities. Series design: hexagonal head.

Materials represented by the variants: Steel.

Documented series dimensions: thread Ø 6 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Concrete, Cracked concrete, Masonry. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT Vite per calcestruzzo JC2-IT · dimensional and installation characteristics
Part number and sourceThread Ø (mm)Hole depthDrill Ø (mm)
EJOT 96500715136.040.06.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT JC6-FR vite per calcestruzzo in acciaio inox A4 · Concrete and masonry screwsJC6-FR vite per calcestruzzo in acciaio inox A4EJOT · 3 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
EJOT JC6-FR vite per calcestruzzo in acciaio inox A4 · Concrete and masonry screws
Series reference image · EJOT

Series characteristics JC6-FR vite per calcestruzzo in acciaio inox A4

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Stainless A4.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT JC6-FR vite per calcestruzzo in acciaio inox A4 · dimensional and installation characteristics
Part number and sourceEmbedmentdepth h nom ≥drill hole depth h 1Drill Ø (mm)
EJOT 965007199345556.0
EJOT 965007199445/5555/656.0
EJOT 965007199645/5555/656.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT JC6-ST vite per calcestruzzo in acciaio inox A4 · Concrete and masonry screwsJC6-ST vite per calcestruzzo in acciaio inox A4EJOT · 4 referencesThreaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.Full description and technical table ↓
EJOT JC6-ST vite per calcestruzzo in acciaio inox A4 · Concrete and masonry screws
Series reference image · EJOT

Series characteristics JC6-ST vite per calcestruzzo in acciaio inox A4

Threaded anchor engaging the substrate after preparation of the specified hole. Thread diameter, drill-bit diameter and installation depth are distinct quantities.

Materials represented by the variants: Stainless A4.

Substrates mentioned in the series sources: Concrete, Cracked concrete. Check the application scope for the individual part.

Follow the specified hole cleaning, equipment, depth and torque or installation limits. Reusability, adjustment and reduced distances must be documented for the part; they are not universal concrete-screw features.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT JC6-ST vite per calcestruzzo in acciaio inox A4 · dimensional and installation characteristics
Part number and sourceEmbedmentdepth h nom ≥drill hole depth h 1Drill Ø (mm)
EJOT 965007198545556.0
EJOT 965007198645/5555/656.0
EJOT 965007198745/5555/656.0
EJOT 965007199045/5555/656.0

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Anchor finder

Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.

Request technical review or a quotation

Select a finder reference or describe the application.

The summary is transferred to the contact form for your review and submission.

FAQ

How do I select an anchor?

Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.

Does equal diameter mean equal capacity?

No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.

Do all anchors have an ETA and CE marking?

These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.

What information is needed for an enquiry?

Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.

Sources and documentation

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Tecfi · EJOT

Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.

Dueemme Sidol
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.