Industrial fixings · Dueemme Sidol

Sleeves and components for bonded anchors

Mesh sleeves and metal components must be matched to the specified bonded-anchor system. In perforated substrates, a sleeve may contain the resin and control anchorage formation.

Tecfi PM01 · Sleeves and components for bonded anchors
Family example · Tecfi PM01

Features and selection criteria

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Designs, materials and substrates

This family contains 9 series or reference groups, with 69 catalogue rows. Series photographs help distinguish geometries and fixing methods; they do not necessarily represent every size in the range.

Documented materials

Steel · Stainless A4 · Other polymers · Resin

Substrates mentioned in the sources

Masonry · Perforated masonry

This list describes the family and does not assign every substrate to every variant.

Information to define before selection

ParameterWhat to check
Load-bearing substrateMaterial type, strength, any cracking, useful thickness and hole conditions. Compatibility must be established for the selected design and size.
Fixing geometryTotal length, body or thread diameter and drill diameter are distinct parameters. Through-fixings must allow for fixture thickness and non-load-bearing layers.
Depth and distancesCompare hole depth, nominal or effective anchorage depth, edge distances and spacing. A deeper hole does not automatically increase fixing capacity.
Environment and exposureCheck material and coating of all components, temperature and service conditions. A2, A4 and HCR stainless designs require selection appropriate to the environment.
Loads and documentationDefine action directions and combinations and check the part-specific document. Dimensional data identify the part but do not replace a design verification.

Installation sequence to verify

  1. Identify the resin system to which the combination belongs.
  2. Compare sleeve, hole and rod diameter and length.
  3. In perforated substrates install the sleeve in the prescribed position.
  4. Follow the resin quantity, sequence and timing for the complete system.

This sequence guides the reading of the instructions. Diameters, depths, equipment and tightening values remain those of the specific variant.

Series and technical tables

Tecfi DAF02 · Sleeves and components for bonded anchorsDAF02Tecfi · 9 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.Full description and technical table ↓
Tecfi DAF02 · Sleeves and components for bonded anchors
Series reference image · Tecfi

Series characteristics DAF02

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.

Materials represented by the variants: Steel.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi DAF02 · dimensional and installation characteristics
Part number and sourceMisura MLength L (mm)Inserimento hefCodolo esagonale
Tecfi DAF 02 08 110M8110805
Tecfi DAF 02 10 130M10130907
Tecfi DAF 02 12 160M121601108
Tecfi DAF 02 12 220M122201658
Tecfi DAF 02 16 190M1619012512
Tecfi DAF 02 16 260M1626019012
Tecfi DAF 02 20 260M2026017012
Tecfi DAF 02 24 300M2430021013
Tecfi DAF 02 30 380M3038028013

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi DAF72 · Sleeves and components for bonded anchorsDAF72Tecfi · 7 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.Full description and technical table ↓
Tecfi DAF72 · Sleeves and components for bonded anchors
Series reference image · Tecfi

Series characteristics DAF72

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.

Materials represented by the variants: Stainless A4.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi DAF72 · dimensional and installation characteristics
Part number and sourceMisura MLength L (mm)Inserimento hefCodolo esagonale
Tecfi DAF 72 08 110M8110805
Tecfi DAF 72 10 130M10130907
Tecfi DAF 72 12 160M121601108
Tecfi DAF 72 16 190M1619012512
Tecfi DAF 72 20 260M2026017012
Tecfi DAF 72 24 300M2430021013
Tecfi DAF 72 30 380M3038028013

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi DAT02 · Sleeves and components for bonded anchorsDAT02Tecfi · 24 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.Full description and technical table ↓
Tecfi DAT02 · Sleeves and components for bonded anchors
Series reference image · Tecfi

Series characteristics DAT02

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi LN01 · Sleeves and components for bonded anchorsLN01Tecfi · 6 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.Full description and technical table ↓
Tecfi LN01 · Sleeves and components for bonded anchors
Series reference image · Tecfi

Series characteristics LN01

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.

Materials represented by the variants: Steel.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi LN01 · dimensional and installation characteristics
Part number and sourceMisura MLength L (mm)
Tecfi LN 01 08 110M8110
Tecfi LN 01 10 130M10130
Tecfi LN 01 12 160M12160
Tecfi LN 01 16 190M16190
Tecfi LN 01 20 260M20260
Tecfi LN 01 24 300M24300

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi FV01 · Sleeves and components for bonded anchorsFV01Tecfi · 7 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: mesh sleeve.Full description and technical table ↓
Tecfi FV01 · Sleeves and components for bonded anchors
Series reference image · Tecfi

Series characteristics FV01

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: mesh sleeve.

Materials represented by the variants: Other polymers.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi FV01 · dimensional and installation characteristics
Part number and sourceDiameter Ø (mm)Length L (mm)Drill Ø d₀ (mm)Profondità foro h1 (mm)Idoneo per accessori MPart-specific documentation indicators
Tecfi FV 01 12 045124512506 ÷ 8—
Tecfi FV 01 12 060126012656 ÷ 8—
Tecfi FV 01 12 080128012906 ÷ 8ETA-CE
Tecfi FV 01 15 085158515958 ÷ 10ETA-CE
Tecfi FV 01 15 13015130151408 ÷ 10—
Tecfi FV 01 15 13515135151458 ÷ 10ETA-CE
Tecfi FV 01 20 0852085209510 ÷ 12ETA-CE

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi PM01 · Sleeves and components for bonded anchorsPM01Tecfi · 4 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: mesh sleeve.Full description and technical table ↓
Tecfi PM01 · Sleeves and components for bonded anchors
Series reference image · Tecfi

Series characteristics PM01

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: mesh sleeve.

Materials represented by the variants: Steel.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi PM01 · dimensional and installation characteristics
Part number and sourceDiameter Ø (mm)Length L (mm)Drill Ø d₀ (mm)Idoneo per accessori M
Tecfi PM 01 12 100101000126 ÷ 8
Tecfi PM 01 16 100141000168 ÷ 10
Tecfi PM 01 22 1002010002212 ÷ 16
Tecfi PM 01 30 1002810003016 ÷ 22

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Tecfi FZ01 · Sleeves and components for bonded anchorsFZ01Tecfi · 4 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.Full description and technical table ↓
Tecfi FZ01 · Sleeves and components for bonded anchors
Series reference image · Tecfi

Series characteristics FZ01

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element.

Materials represented by the variants: Steel.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

Tecfi FZ01 · dimensional and installation characteristics
Part number and sourceDiameter Ø (mm)Length L (mm)Filetto interno M
Tecfi FZ 01 06 048848M6
Tecfi FZ 01 08 0831280M8
Tecfi FZ 01 10 0831480M10
Tecfi FZ 01 12 0831680M12

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT Bussola retinata USF · Sleeves and components for bonded anchorsBussola retinata USFEJOT · 5 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: mesh sleeve.Full description and technical table ↓
EJOT Bussola retinata USF · Sleeves and components for bonded anchors
Series reference image · EJOT

Series characteristics Bussola retinata USF

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: mesh sleeve.

Documented series dimensions: length 80–130 mm. Endpoints describe the listed sizes rather than a continuous range. Use the part-specific row for each combination.

Substrates mentioned in the series sources: Masonry, Perforated masonry. Check the application scope for the individual part.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT Bussola retinata USF · dimensional and installation characteristics
Part number and sourceLength (mm)Drill bit Ø (mm)Hole depth ≤ (mm), source wordingCompatible thread
EJOT 957101208080.012.085.0M8
EJOT 957101608585.016.085.0M8, M10
EJOT 9571016130130.016.0135.0M8, M10
EJOT 957102008585.020.090.0M12-M16
EJOT 9571020130130.020.0135.0M12-M16

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

EJOT Calzetta SH · Sleeves and components for bonded anchorsCalzetta SHEJOT · 3 referencesComponent for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: vinylester formulation, epoxy formulation.Full description and technical table ↓
EJOT Calzetta SH · Sleeves and components for bonded anchors
Series reference image · EJOT

Series characteristics Calzetta SH

Component for the specified bonded-anchor combination. Geometry, dimensions and material must be compatible with resin, substrate and threaded element. Series design: vinylester formulation, epoxy formulation.

Materials represented by the variants: Resin.

Substrates mentioned in the series sources: Perforated masonry. Check the application scope for the individual part.

Check diameters, lengths, rod and resin quantity in the system instructions. Do not substitute components solely because their threads match; generic rods already covered elsewhere in the catalogue are not duplicated here.

The table lists available characteristics for each reference; alternative installation configurations remain separate. Refer to the linked documents for torque, loads and conditions not specified in the table.

View the manufacturer’s product page ↗

Part-specific technical table

Values and symbols follow the source. “—” = not stated in the table, not zero. The std, red1 and red2 designations identify different manufacturer configurations.

EJOT Calzetta SH · dimensional and installation characteristics
Part number and sourceDrill bit Ø (mm)Hole depth ≤ (mm), source wordingCompatible thread
EJOT 957001208012.085.0M8
EJOT 957001513016.0135.0M8-M12
EJOT 957002008520.090.0M12

ETA, fire or seismic indicators listed for one part do not extend to other sizes. Permissible loads and torque values not listed here must be obtained from the applicable document and actual configuration.

Anchor finder

Search by part number or select declared characteristics. Missing data do not satisfy a dimensional filter.

Request technical review or a quotation

Select a finder reference or describe the application.

The summary is transferred to the contact form for your review and submission.

FAQ

How do I select an anchor?

Start with substrate, load and environment, then identify configuration, depth, distances and part-specific documentation. The finder selects catalogue references and does not perform a design check.

Does equal diameter mean equal capacity?

No. Geometry, material, anchorage and technical assessment may differ. Dimensional comparison does not establish technical equivalence or interchangeability.

Do all anchors have an ETA and CE marking?

These cannot be assigned to an entire category. Check the product documentation, scope and applicability to the specific size. An ETA link does not extend its assessment to other parts.

What information is needed for an enquiry?

Part number or family, quantity, substrate material and condition, thicknesses, fixing geometry, environment, actions and required documents. For resins, also specify temperature and hole conditions.

Sources and documentation

Dimensions transcribed from the listed sources, checked on 13 November 2026. “—” means not stated or not normalised, not zero. Nominal diameter, thread and drill diameter are distinct. Consult the specific variant documentation for loads, installation and permitted applications. Availability is confirmed at quotation.

Tecfi · EJOT

Dueemme Sidol S.r.l. · Sesto San Giovanni, Milan · Supply for industrial customers and OEMs.

Dueemme Sidol
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.